Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Brandenberger

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Probably about 450lbs? Doesn't it look like the...

    Probably about 450lbs? Doesn't it look like the one in this book for the 3K?

    http://vintagemachinery.org/pubs/2098/17371.pdf
  2. Replies
    6
    Views
    939

    I have what looks like a NOS Buck L-00 taper...

    I have what looks like a NOS Buck L-00 taper backing plate, doesn't look like it's ever been mounted. PM me with your email address and I can send you pictures if you're interested.

    -Phil
  3. Not sure if you've tried these guys Cincinnati...

    Not sure if you've tried these guys Cincinnati Repair Parts, I think they have quite a lot of cinci parts (no affiliation, never bought from them).
  4. Replies
    6
    Views
    843

    Van Norman 12's show up with some reasonable...

    Van Norman 12's show up with some reasonable frequency... a month ago one sold at auction in Union City NJ for $200 or so, with collets. Maybe that would be stout and yet not massive?

    -Phil
  5. wanted: service / maintenance manual for K&T 205 SA

    Hi,
    Anyone have the service manual for this machine? VintageMachinery has the one for the 205 S-12 but that machine is quite different.

    I have the installation, operation and parts manuals but...
  6. Replies
    2
    Views
    608

    Pulled the table. 333646 no scoring, which...

    Pulled the table.

    333646

    no scoring, which is good. Flaking worn off the ends of the saddle. Grease gun filled with oil forces lubrication through some of the lines, will have to check them...
  7. Replies
    2
    Views
    608

    K&T 205 SA cleanup

    Just starting to cleanup a 1965 K&T 205 SA horizontal.

    So far I've drained the knee and column and refilled with kerosene.

    A few questions:

    - machine's sight glasses on column and knee are...
  8. Replies
    11
    Views
    1,915

    B&S 510, if you unscrew the shield for the...

    B&S 510, if you unscrew the shield for the vertical height screw can be 75" tall, with the
    head lowered most of the way.

    You could remove it from the base cabinet (3 bolts from inside the base)...
  9. Picked up machine today, included original...

    Picked up machine today, included original documentation.

    332782

    332781
  10. Thanks, I hadn't found that particular one, very...

    Thanks, I hadn't found that particular one, very helpful thanks!
  11. K&T 205 SA vertical head compatibility?

    Hi,

    I picked up a very nice original owner K&T 205 SA today, however doesn't have a vertical head.

    I'm wondering whether aside from the drive gear differences, whether vertical heads for 2H,...
  12. Not the exact right machine, but these pictures...

    Not the exact right machine, but these pictures show a crane that attaches to the overarm.

    Photo Index - Cincinnati Milling Machine Co. (Milacron) - Cincinnati 2L horizontal mill |...
  13. I don't think it is a great idea to run the motor...

    I don't think it is a great idea to run the motor at fractional speed. As you know, it means they'll be proportionally less lubrication flow, same for coolant, and the motor fan speed. So really...
  14. I'm far from an expert on these mills, others can...

    I'm far from an expert on these mills, others can chime in, probably other people who run these on VFDs too. But my thoughts:

    - If you wanted to disable the on/off switch on the clutch handle...
  15. I remember this thread... not on PM but... ...

    I remember this thread... not on PM but...

    Broken Hearted... My new to me 1942 Van Norman No.12 Spindle Ring and Pinion shot - The Home Machinist!
  16. I recently was looking at a K&T mill and no...

    I recently was looking at a K&T mill and no 3phase power was available, so I took a VFD with me and wired it up and ran it. This was a 5hp machine, the only VFD I had lying around was a 2hp.

    To...
  17. I assume similar or identical to my B&S 510 SG. ...

    I assume similar or identical to my B&S 510 SG. The process is pretty annoying... as I recall:

    - give yourself access from the front, by either removing or at least releasing and sliding up/down...
  18. Ah, I see that now. Thanks! Too bad they don’t...

    Ah, I see that now. Thanks! Too bad they don’t show the mounting bracket piece that attaches to the machine. If anyone has one a picture of that would be very useful.
  19. Was there a Cincinnati No 2 crane for vertical heads?

    Hi,

    Looking at a Cincinnati 2ML with the heavy vertical head locally,
    nice machine. I have seen a few mentions of a "overhead crane" for this,
    maybe like a K&T parking attachment for the...
  20. I bought a Flair suction-type pump: KBC,1PH...

    I bought a Flair suction-type pump:

    KBC,1PH 110/220V SELF-CONTAINED COOLANT PUMP,1-456-035,KBC Tools & Machinery

    Haven't tried it yet, but it fits in the coolant pump area and should work....
  21. Free for Shipping: Monarch 10ee Ruthman D-500 Coolant Pump 3ph

    Hi,
    Removed a Rumaco D-500 coolant pump (3ph 1/10hp) from a 1962 Modular 10ee.

    330885

    Pump was originally non-functional, leads had shorted due to insulation failure and impeller was frozen....
  22. Pump is still available, $75 plus shipping OBO.

    Pump is still available, $75 plus shipping OBO.
  23. Replies
    14
    Views
    613

    Any reason not to get a VFD with single phase...

    Any reason not to get a VFD with single phase input? Either use a bigger one derated on single phase or one designed for single phase input. And connect before the phase converter of course, not...
  24. FS: 1/8 hp 3ph Flair coolant pump unused

    Coolant pump just like this one

    KBC,3PH 220/440V DELUXE SHAFT COOLANT PUMP,1-456-050,KBC Tools & Machinery

    unused/like new in box, I bought a new 3phase Kent lathe and exchanged the 3phase...
  25. Replies
    23
    Views
    2,352

    I think you’ll find the chain type on the hoists...

    I think you’ll find the chain type on the hoists is hard to match, and it needs to be a correct fit to work.

    You will also find having excess chain on a lever hoist normally is annoying, though at...
Results 1 to 25 of 380
Page 1 of 16 1 2 3 4