Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: aerowizard

Search: Search took 0.00 seconds.

  1. Philabuster, thank you so much for explaining...

    Philabuster, thank you so much for explaining that. I will study this and apply it immediately. I usually get jobs like this and without training, I sometimes struggle with things that Esprit could...
  2. How would you program this large radius, on a small part?

    I've yet to figure out how to program this type of behavior. I am using Mazatrol Fusion 640T on a QT-250 from like '87. Can someone give me some values or a picture of how they would program this...
  3. After making a parameter change like this, did...

    After making a parameter change like this, did you kill the main power to the machine twice? I was told by Mazak when we make these changes, main switch off for 5 seconds, on for 5, off for 5, on for...
  4. Replies
    8
    Views
    3,099

    When my QT250 throws this alarm, I have to loosen...

    When my QT250 throws this alarm, I have to loosen the motor mount up on the conveyor to allow the chain to free itself. Then I can simply re-tighten the mounts back down and hit reset.
  5. Replies
    3
    Views
    678

    I know that my QT250 has the backup battery in...

    I know that my QT250 has the backup battery in the panel, in the rear with all the circuit boards and such. But also, I found one behind the screen. Try looking around in there. It was the same...
  6. Replies
    3
    Views
    691

    I was able to figure it all out. I understand I...

    I was able to figure it all out. I understand I didn't have a designated groove width in the line. My point was I couldn't figure out what it needed to be. Really any of it. After 4 molds, I was able...
  7. Replies
    3
    Views
    691

    Fusion 640T ID Groove complications

    Attached you will find pictures of what I could come up with as far as a program goes. I get an alarm for illegal designated tool width on sequence 12 and it wont let me go any further. I have a tool...
  8. Replies
    0
    Views
    328

    Fusion 640T ID Groove complications

    Attached you will find pictures of what I could come up with as far as a program goes. I get an alarm for illegal designated tool width on sequence 12 and it wont let me go any further. I have a tool...
  9. Replies
    13
    Views
    841

    Yes it does. But I want .00001 notice its the 5th...

    Yes it does. But I want .00001 notice its the 5th decimal place. I want to be able to comp the machine in 50-millionths in standard measurement.
  10. Replies
    13
    Views
    841

    samsung sl20 tool comp paramater change

    Is it possible to add another decimal place to the tool comp section so I can comp it .00005 instead of .0005?
    IF anyone knows, please help. I'm running a +/- .0001 dimension and clearly its a back...
  11. There should be no flat walls in the groove. I...

    There should be no flat walls in the groove. I will get a picture up shortly so yall can see the groove itself. This is not an easy task, but i know it can be done.
  12. Mazatrol fusion 640T. IS this what you are...

    Mazatrol fusion 640T.
    IS this what you are implying?
  13. Sir, I'm not burying that tool to its full width...

    Sir, I'm not burying that tool to its full width amount. You can use a .08 FNR groover to achieve a .059 simply by not allowing it to go past .059 worth of its width.
  14. Generating full nose radius od grooving sequence

    Hello, I am currently tasked to make some grooves! Usually quite simple, however I can not get rid of the chatter. So to avoid all the nonsense leading up to this, I'm looking to figure out how to...
  15. This is a one time deal, though they talked about...

    This is a one time deal, though they talked about "if it were a really nice gage" they would consider heat treating it and etching a gage # on it for future use. Which I don't agree with as this is...
  16. Creating Thread Gaging for Internal Threads

    I've got a 4 1/4-12 3B internal thread I need to make a plug gauge for. I've got the machinery handbook however I'm having a hard time understanding everything going on in it.If someone could throw...
  17. none. i've just been re-programming everything...

    none. i've just been re-programming everything that comes through now in the shop. getting old, but i'm getting good!
  18. Mazatrol Fusion 640 515 CMT Misconnected (2, -4, 0 )

    Suddenly I can not transfer programs to/from DNC. Using ENETDNC with CMT I/O has always worked on this machine. Re-ended the ethernet cable and the tester says its good to go. Replaced the RSD232 of...
Results 1 to 18 of 19