Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: sneebot

Page 1 of 43 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    26
    Views
    1,995

    Peter, I have not tried to power up the machine...

    Peter,
    I have not tried to power up the machine yet. I may not get to that for a few weeks. I haven't looked at the control voltage yet.

    I'd like a parts manual to start with. I may ping you...
  2. Replies
    26
    Views
    1,995

    No, it has been repainted. Not a horrible job but...

    No, it has been repainted. Not a horrible job but not great either.

    Sony DRO, surprisingly, powers up but shows errors on all the axis. Screen has some extreme burn in. In needs clean up and the...
  3. Replies
    26
    Views
    1,995

    Arrived today. Just for Don-- backlash X ~0.006"...

    Arrived today.
    Just for Don-- backlash X ~0.006" ~Y 0.007"

    It's filthy but all there. The Sony DRO is a replacement-- The Sony scale is mounted under the table but the original scale looks to...
  4. Replies
    31
    Views
    2,743

    YRC has indeed lost the crate a 2nd time.

    YRC has indeed lost the crate a 2nd time.
  5. Replies
    31
    Views
    2,743

    I may have spoken too soon, it looks like they...

    I may have spoken too soon, it looks like they may have lost this again.
  6. Replies
    26
    Views
    1,995

    Looking around to see if I had a manual for this...

    Looking around to see if I had a manual for this machine I found the Reliable machine-- this was sold at the same time as Ross' machine. It certainly seems to have the same DRO box as the machine...
  7. Replies
    31
    Views
    2,743

    The address is written directly on the crate with...

    The address is written directly on the crate with a large marker. Being paranoid I also put a copy of the BOL in the crate. I've always been a bit suspicious of taping or adhearing labels to wood...
  8. Replies
    31
    Views
    2,743

    Well it looks like this has turned out well. YRC...

    Well it looks like this has turned out well. YRC located the crate without too much prodding on my part. Apparently they delivered it to the wrong address with some other crates. They still need to...
  9. Replies
    31
    Views
    2,743

    Yellow Freight (YRC) Lost a Crate

    Recently I shipped a crate of machine parts from Massachusetts to Wisconsin via YRC. Crate was 24"x50" by~6" high and weighed in at ~240#.

    It was a few days past their estimated delivery date with...
  10. Replies
    26
    Views
    1,995

    The gray color of the machine is just rust...

    The gray color of the machine is just rust preventative-- it's green underneath and brand new.


    It apparently came out of Boeing or a division thereof.
  11. Replies
    26
    Views
    1,995

    I have had some bad luck with freight companies...

    I have had some bad luck with freight companies recently. I shipped out a set of Taft Peirce ways (from a Taft Peirce #2- so basically impossible to find) to get reground and the crate has gone...
  12. Replies
    26
    Views
    1,995

    Guilty. I'll let you know.

    Guilty.
    I'll let you know.
  13. I'll take F & G.

    I'll take F & G.
  14. Replies
    0
    Views
    456

    Pope Grinding Spindle

    For sale is a Pope grinding spindle. Body of the spindle is 3"OD x ~12-5/8".
    This is a 3 phase 220V 3600 RPM motor.
    This was in a wood crate and had the notations shown. I cannot verify one way or...
  15. Thread: Stack Bins

    by sneebot
    Replies
    0
    Views
    444

    Stack Bins

    Pick up only- Boylston, Massachusetts

    pick up only- Boylston, Massachusetts

    Set of stack bins--Approximate dimensions: 19" deep, 37" wide and 7" high (for each level).

    Six are shown but I...
  16. Here is the parts diagram I have of the TP...

    Here is the parts diagram I have of the TP spindle...

    260412
  17. I've never had a TP spindle apart but this...

    I've never had a TP spindle apart but this certainly looks like the drawings in the TP parts manual I have. What does the motor housing look like?
  18. Replies
    2
    Views
    967

    A bad Deckel idea

    Up on ebay an auction shows this:

    260160

    I haven't seen anyone try this combination of machine/ heads. The FP2 head seems a bit large for an FP1, not to mention the probable mismatch of gearing...
  19. Replies
    0
    Views
    466

    Standard Grinder Point Arbor

    I recently acquired a Taft Peirce high speed spindle. It came with the arbor pictured below. Is this a standard grinder point arbor?

    I've seen some references to high speed Erickson Collet...
  20. Replies
    19
    Views
    1,645

    I followed part of it, did not purchase anything.

    I followed part of it, did not purchase anything.
  21. Replies
    19
    Views
    1,645

    Those are not Jig Grinding heads but Jig Boring...

    Those are not Jig Grinding heads but Jig Boring heads. The Jig Grinding heads were sold with the LK machines (at the auction).

    Unless your wife is quite stout I'd leave her out of it. Both types...
  22. Replies
    15
    Views
    1,742

    Ditto on that one.

    Ditto on that one.
  23. Replies
    6
    Views
    1,048

    Deckel FP4's (2700-xxxx machines) have ball...

    Deckel FP4's (2700-xxxx machines) have ball screws on the Z axis-- not really the axis of interest in this case.
  24. available from Amazon for $344.86 My guess is...

    available from Amazon for $344.86

    My guess is they'll ship it cheaper than you will as well.
  25. Replies
    8
    Views
    1,033

    I sent you a PM.

    I sent you a PM.
Results 1 to 25 of 1071
Page 1 of 43 1 2 3 4