Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Anhur

Search: Search took 0.00 seconds.

  1. I considered doing the same thing for another...

    I considered doing the same thing for another barreled action. After I estimated the time in reverse engineering the action, drawing up a chassis, buying material stock and machining it. I...
  2. Replies
    23
    Views
    3,579

    That seems like it is always an issue. I had the...

    That seems like it is always an issue. I had the same problem with a .308 Savage I built. The only rounds I have loaded up with so far are a Nosler 130gr and a Hornady 140 ELD-M and they both fit...
  3. Replies
    23
    Views
    3,579

    Thanks for all the comments and suggestions. I...

    Thanks for all the comments and suggestions. I decided that in the end even if it only makes a small difference I would change the barrel out for a new one. I am pretty confident that the offset...
  4. Replies
    23
    Views
    3,579

    I would agree. The tests I have been conducting...

    I would agree. The tests I have been conducting have been all sitting on a bench with a bipod and a bag. I don't claim to be a great shooter, but I have done some classes and have shot other rifles...
  5. Replies
    23
    Views
    3,579

    I looked up Mike Bellm and found that article on...

    I looked up Mike Bellm and found that article on his website. Looks exactly like the chamber cast I have. It seems that the general consensus is the barrel was chambered off center.



    I...
  6. Replies
    23
    Views
    3,579

    Uneven Rifling Wear or Bad Chambering?

    Hey all, I recently purchased a used Savage 12 chambered in 260 Remington. I have taken it to the range several times in an effort to get it grouping up. It has however been resisting my best...
  7. Replies
    14
    Views
    2,814

    What's interesting is I have a couple of other...

    What's interesting is I have a couple of other Mosin Nagant Rifles and they all slug right at 0.313" and those shoot way better with the .311's despite being in old wood stocks with iron sights. ...
  8. Replies
    14
    Views
    2,814

    I haven't fired it outside of the stock, however...

    I haven't fired it outside of the stock, however it has been fired with the original wood stock and the plastic stock with the same results.

    Pic of the rifle and one of the bolt head.
    253367...
  9. Replies
    14
    Views
    2,814

    The rifle grooves measured in at 0.313" and the...

    The rifle grooves measured in at 0.313" and the lands at 0.301". From my understanding that is typical of a good bore Mosin Nagant and should fire the 0.311"-0.312" stock sized bullets without much...
  10. Replies
    14
    Views
    2,814

    I will try some at a closer distance. My next...

    I will try some at a closer distance. My next trip to the range I am going to hand-load some different powder charges. Maybe I'm just way off the node??? I did check the headspace when I got it,...
  11. Replies
    14
    Views
    2,814

    Garbage Rod Accuracy

    Hey all, I have an old Mosin Nagant 91/30 rifle that started life in 1943 in Izhevsk Russia. Being a midwar non-Tula round receiver with nothing special to be spared for I hacked it up some years...
  12. Replies
    8
    Views
    1,492

    I could make an angle fixture, but I have only...

    I could make an angle fixture, but I have only run these parts twice. I guess the appeal of a tilting vise was the ability to change angles easily for future jobs.
  13. Replies
    8
    Views
    1,492

    That's basically what I'm doing now, but clamping...

    That's basically what I'm doing now, but clamping a smaller vise in my 3600v seems to be difficult to keep it all square as it distorts the more I tighten the 3600v.
  14. Replies
    50
    Views
    8,338

    I have engraved the few lowers that I have...

    I have engraved the few lowers that I have created. I don't know if it's necessary legally or not. Being in Texas it probably doesn't matter, but I always envisioned the pain that could be created...
  15. Replies
    8
    Views
    1,492

    Sine Vise For Milling

    Hey All, I have a new Haas TM1P vertical mill and a need to hold some flat 304 stainless parts at a 45° angle to mill a 90° slot in the sides. Last time I did this I mounted a small vise inside of...
  16. Question about fabricating large frame parts

    Hello all,

    I am working on a project that is going to be a large frame component for mounting some precision equipment onto a vehicle frame. The frame will be made out of some 3"x2" 1/8th wall...
  17. Replies
    2
    Views
    683

    Haas TM1P Phantom Directory In Memory

    Hey all,

    I have an almost new TM1P that has a small glitch in the memory. To be fair I know for a fact I created this issue. It is common for me to use a flash drive to transfer the nc from my...
  18. Replies
    18
    Views
    3,915

    A custom mount would have been difficult. The...

    A custom mount would have been difficult. The holes were not square to the top of the receiver and not in alignment with each other. Picture the beginnings of a radial engine. It was a hack job...
  19. Replies
    18
    Views
    3,915

    I used two pieces of stainless rod turned down...

    I used two pieces of stainless rod turned down .010" under the hole size. Took and heated them to just over bright red and inserted one in the hole. Left it in the hole for a few minutes until it...
  20. Replies
    18
    Views
    3,915

    I did end up spot annealing the areas around the...

    I did end up spot annealing the areas around the holes. That made the steel workable and I was able to tap the holes. There was just no way to cut the holes with the steel being that hard. Thanks...
  21. Replies
    18
    Views
    3,915

    At this point I am about ready to use JB Weld and...

    At this point I am about ready to use JB Weld and some hose clamps.

    All kidding aside I ran out to the local machine tool store and picked up a few items I may or may not try on Monday. I found a...
  22. Replies
    18
    Views
    3,915

    Trouble Drilling Receiver

    Hey all. I have an old bolt action rifle that had a scope installed with a mount bolted to the top of the receiver. Unfortunately it was drilled and bolted crooked originally and I wanted to repair...
Results 1 to 22 of 22