Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: plastikdreams

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. I had to sign a nda to get my current position...

    I had to sign a nda to get my current position lol.
  2. Wire edm...if you have the time lol

    Wire edm...if you have the time lol
  3. Whenever we have a tech come out to give our mits...

    Whenever we have a tech come out to give our mits wire a pm there's always something(s) that need to be adjusted or fixed....this last visit the upper head was replaced, he left the metal piece off...
  4. Thanks to those who responded! Clausing finally...

    Thanks to those who responded! Clausing finally got back to us so we will be ordering from them.
  5. Quote for truth

    Quote for truth
  6. Thanks for the info, motion may have a chance...

    Thanks for the info, motion may have a chance with us....we are a large co and purchasing can be an issue with itar and our other regulations. Quite frankly it's a pain in the ass lol.
  7. No problem

    No problem
  8. You don't check your paths before you run?

    You don't check your paths before you run?
  9. Adaptive control only deals with the feed rate...

    Adaptive control only deals with the feed rate and current levels during the cut. Basically it smooths the cut and keeps the wire from braking.
  10. Where to buy clausing 5914 lathe drive belts

    At work on our clausing 5914 the drive belt from the motor decided to explode, and while I'm in there I might as well change the other belt as it has to come off to get the other on. We have...
  11. Do it all the time when I need accuracy....make a...

    Do it all the time when I need accuracy....make a shoulder on it so it does5 slide into the jaws.
  12. We carry a 20# abc and a 20# d on the engine.weve...

    We carry a 20# abc and a 20# d on the engine.weve dropped an entire d on an old Astro van...there was so much magnesium in the dash and steering column it did nothing. Ended up having 2 hose lines,...
  13. Replies
    689
    Views
    87,343

    If he did that the entertainment value would drop...

    If he did that the entertainment value would drop off the e-cliff.
  14. I highly doubt it's gonna work...short of burning...

    I highly doubt it's gonna work...short of burning them in on a sinker
  15. If you can't put it out with a 10# abc and you...

    If you can't put it out with a 10# abc and you haven't called us already...you better get on the phone asap
  16. Replies
    35
    Views
    2,648

    Sounds like you need to make a deal to work at...

    Sounds like you need to make a deal to work at someone's shop overseas. I'm sure there are guys on here up for the challenge.
  17. Replies
    1,938
    Views
    106,550

    Meh I don't see it...we would need to see if the...

    Meh I don't see it...we would need to see if the ip addys are the same
  18. Shitty situation. Lots of split second decisions...

    Shitty situation. Lots of split second decisions occuring in a short amount of time.
  19. Replies
    1,938
    Views
    106,550

    Can you substantiate this?

    Can you substantiate this?
  20. Replies
    27
    Views
    3,513

    That's a huuuuuge bitch!

    That's a huuuuuge bitch!
  21. Replies
    21
    Views
    1,969

    Both actually...weird right

    Both actually...weird right
  22. Replies
    22
    Views
    2,434

    Moist I have worked with were good to around...

    Moist I have worked with were good to around 15-20 degrees. It all depends on the flush cups, machine u,v movement, and tank size. The part dimensions can affect the amount of angle that can be cut....
  23. Replies
    21
    Views
    1,969

    TiCN is a great coating as well. And it behaves...

    TiCN is a great coating as well. And it behaves with aluminium.
  24. Replies
    21
    Views
    1,969

    I do t know about your application but for...

    I do t know about your application but for cutters I've always had good luck with AlTiCN...not good with aluminum. For aluminum I'd go with ZrN coated.
  25. If you can get pictures it would probably help a...

    If you can get pictures it would probably help a bunch...and/or a description of the table
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4