Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: TrollTuner

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. 16K Brother for 4 years. The first couple we...

    16K Brother for 4 years. The first couple we had severely overloaded 100A 3phase ~220v " wild leg" It would beep the battery backups in the shop and across the street when the lathe tool...
  2. Replies
    16
    Views
    1,255

    I am here to hopefully learn something. ...

    I am here to hopefully learn something. Secretly looking for the pic of the riggers dropping the machine on its face or the truck stuck in a culvert and the forklift on two wheels..
  3. Replies
    1
    Views
    1,026

    They finally installed the parts catcher. While...

    They finally installed the parts catcher. While the tech was here he used the included ( with the original install conveyor kit, I saved all the "spare" parts.) contactor and wiring. Now the...
  4. Replies
    10
    Views
    883

    The video is private but that sounds ominous.. ...

    The video is private but that sounds ominous.. Was hoping you got it sorted.
  5. Connector from Digikey. Theres a page in the...

    Connector from Digikey. Theres a page in the manual for the pin out.



    273767
  6. Replies
    1
    Views
    1,026

    Genos L2000 Conveyor Estop

    Newly installed Genos L2000 The conveyor isn't controlled by M codes. Only the buttons on the conveyor discharge.

    Conveyor Runs with door open. (This is somehwat ok) and is not shut down...
  7. Replies
    30
    Views
    2,518

    Yes the Big MGR42 collets will hold on no...

    Yes the Big MGR42 collets will hold on no matter.. Operator thought i turned the program down when we swapped them for 1/2" helical roughers.. thought they were SK but the Big dual angle of the...
  8. Replies
    8
    Views
    1,778

    It stops working immediately. Your data is...

    It stops working immediately. Your data is theirs...

    There is another fork of the software "fusion entitlement" Its release is a little different.. I assumed it was the same release as the HSM...
  9. This stuff really galls my endmills..

    This stuff really galls my endmills..
  10. Replies
    55
    Views
    6,476

    I have blum Z Nano on the brother for length. I...

    I have blum Z Nano on the brother for length. I prefer it to the renishaw.. Much easier to set up and seems to be resistant to stringy chip encounters. Tiny bit less table space, might get snug...
  11. Replies
    17
    Views
    2,296

    The early (6.2015) Speedio were VactraNr2 like...

    The early (6.2015) Speedio were VactraNr2 like the Haas... I could have waited a bit or probably asked for one at the time, didn't know about it.
  12. Replies
    2
    Views
    1,985

    Windows 10 > OSP300

    Sending files to OSp300 on the network. ( 2016 M560 in this case)
    Logged into the OSP with the password out of the manual.
    MD1 mapped as a drive on windows set to login on login.

    On my windows...
  13. Replies
    43
    Views
    4,447

    I have used the HM390 since they were released. ...

    I have used the HM390 since they were released. Maritool made a custom arbor for the Brother with .5" for the 1.5" HM390-15 Initially that 1.5" holder body wouldn't clear the high positive...
  14. Its in the maintenance manual wiring diagram.

    Its in the maintenance manual wiring diagram.
  15. Replies
    8
    Views
    1,579

    My -05 lathe lost the start capacitor in the...

    My -05 lathe lost the start capacitor in the motor. It was a little tricky to find. Finally at an established electric motor shop. Grainger
    etc was a no. Bit of time and a few bucks later...
  16. Databank > User Parameter (f4)> Switch1 (f1) >...

    Databank > User Parameter (f4)> Switch1 (f1) > Down near the bottom 302


    Great machine but mine seems to loose minutes pretty regularly. Its rarely the correct time. One nice part about the...
  17. Did you find a solution for this?

    Did you find a solution for this?
  18. On My 560 OSP300 The wear is on the Magazine...

    On My 560 OSP300 The wear is on the Magazine info and Tool Data pages as shown in the image above.
  19. My 560v Has Wear. June of 2016 "Tool Wear...

    My 560v Has Wear. June of 2016 "Tool Wear Compensation" was listed on the quote as a no price option. I asked for itemized an it shows as $1900
  20. I have an Okuma M560, Brother S700 16k BBT and a...

    I have an Okuma M560, Brother S700 16k BBT and a Pair of older Haas. Brother came first. It rips on 75% of my parts. The Okuma has sufficient power.

    The Okuma Hicut is nice. Turn it on, If...
  21. Replies
    92
    Views
    8,012

    They promised this quite a few years ago too. ;) ...

    They promised this quite a few years ago too. ;) I would say to buy it on what it does today. Not what it might sometime down the road. Have been using HSM since before they were bought by...
  22. Replies
    24
    Views
    2,417

    The Qualichem 250c turns the soft grips into a...

    The Qualichem 250c turns the soft grips into a nasty goo. You seeing the same thing? Have had poor luck with them, our snapon never stands behind them. Hoping the Milwaukee grips hold up...
  23. Replies
    8
    Views
    891

    Omega should have some. Check out the WT series...

    Omega should have some. Check out the WT series at the bottom of the page.

    Thermocouples
  24. Try Rolled Alloys. They seem to do good on my...

    Try Rolled Alloys. They seem to do good on my smaller orders of cut stainless. Almost always a nice price too.
  25. Replies
    58
    Views
    6,043

    My S700 has more coolant flow than my haas and...

    My S700 has more coolant flow than my haas and Okuma together . When we got the Okuma 560 we thought something was wrong with the coolant. The pump is about 2/3 of the rating or something like that....
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4