Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JST

Page 1 of 60 1 2 3 4

Search: Search took 0.11 seconds.

  1. You need to find out what is being contemplated...

    You need to find out what is being contemplated there. 8k might be reasonable, depending on the house.... 2k SF can be done several ways. Some have more needs-to-be-protected area than others.
    ...
  2. Assuming it is a gas truck, not diesel....... ...

    Assuming it is a gas truck, not diesel.......

    Gas sitting in the truck for 2 years is bad. It probably does not (as mentioned) even smell like gas. It will barely burn. That's enough problem...
  3. Maker likely expected the load motor would have...

    Maker likely expected the load motor would have its own contactor in the machine, which accounts for no output contactor. That is pretty much how it would be if the machine/motor were wired to a 3...
  4. Replies
    6
    Views
    553

    Yeah, that was another item on the list. It just...

    Yeah, that was another item on the list. It just keeps going... there is way more missing than is left. Makes a person wonder about all the hidden things that do not show in the photos.

    If you...
  5. Replies
    6
    Views
    553

    Not an issue... the seller is the clueless (or...

    Not an issue... the seller is the clueless (or greedy) person in this.

    Those 1020s seem like a very nice machine comparable to a 10EE.... Much more generally useful than the 608, which is a...
  6. Replies
    6
    Views
    553

    There is so little left of it that it is really a...

    There is so little left of it that it is really a parts machine in many ways. The entire change gear setup is missing, the tool holder is totally wrong. The headstock appears to be set up for...
  7. While this is probably good advice, not knowing...

    While this is probably good advice, not knowing details, the braking is not more violent than acceleration, I have tested similar sized machines and was unable to get a 6" or a 5: chuck to...
  8. I have a few, I get 'em for a couple bucks at...

    I have a few, I get 'em for a couple bucks at estate sales. Dirty ones go for cheap. Nice shiny ones cost money. All of them work the same, and there are rags and water everywhere.....
  9. If all you have is a 4 way transformer, going in...

    If all you have is a 4 way transformer, going in with 115 on the 480 winding, coming out the 240 and leaving that for 30 min or so, then 115 into 240:240 winding, leaving that for 30 min or so, then...
  10. Replies
    13
    Views
    563

    1", eh? That's more than I have. As far as I...

    1", eh? That's more than I have. As far as I know that (my) machine has a 10" saddle etc, but they are so close that they probably interchange. I have a t-slot crosslide from an 11", and it fits...
  11. It may not turn on. When testing those, I have...

    It may not turn on. When testing those, I have always used a "4 way" transformer, 120/240 to 240/480. other than that, no damage from a basic test of turn on and run. Some can refuse to work if...
  12. Replies
    13
    Views
    563

    What's your distance from compound to spindle...

    What's your distance from compound to spindle center? Some may be larger, my 200 is smaller than most in that dimension.
  13. Replies
    6
    Views
    533

    That thing really does look very well made and is...

    That thing really does look very well made and is quite "pretty". Seems too small for practical use, might it be some sort of sample piece or the like?
  14. Replies
    13
    Views
    563

    Maybe not so fast.... The 200 is really too...

    Maybe not so fast....

    The 200 is really too small for the toolposts. Yes a 10" is big enough, but the distance from compound to spindle center is tiny, like 0.875". iI's marginal on clearance...
  15. "fuse paper"? Good one... had not heard that...

    "fuse paper"? Good one... had not heard that one before.

    Not recommended, of course........
  16. Replies
    36
    Views
    1,801

    it was pretty expensive at one time for balloons...

    it was pretty expensive at one time for balloons and Zeppelins, when it was a product of zinc and acid.... So, in essence, probably yes.

    The real intent is to make "cars" rare and very expensive....
  17. Replies
    36
    Views
    1,801

    The serious problem with hydrogen or any other...

    The serious problem with hydrogen or any other such fuel that must be "created" by some process that itself takes energy, is that it cannot compete.

    When there iis fuel that you can basically...
  18. Replies
    18
    Views
    1,303

    Since you are not afraid (obviously) of some...

    Since you are not afraid (obviously) of some work, you can MAKE the damn arbor in a day from a chunk of 4140 (for the classy job) or even just regular 1018. Spacers are available new from sources...
  19. Replies
    22
    Views
    10,093

    Split rivets are available from McMaster. I do...

    Split rivets are available from McMaster. I do not know if they are available nickel plated, though. But when the steel parts are re-nickel plated, the rivets can be also maybe.

    The...
  20. Replies
    34
    Views
    2,481

    Time was when any blueprint shop had a big camera...

    Time was when any blueprint shop had a big camera with the ability to enlarge to big sizes from originals up to over a foot on a side in some cases. They are gone, even though most turned into places...
  21. OK, you HAVE the PP, and no reason why you cannot...

    OK, you HAVE the PP, and no reason why you cannot use it.

    YES, there are filters. They can be expensive, but so are houses.

    I would have suggested a commercial line filter, BUT.... remember,...
  22. Replies
    6
    Views
    613

    Hmmmmmm....... Motors run on current. Voltage...

    Hmmmmmm.......

    Motors run on current. Voltage "pushes" current through impedance. (yes, I know that power is the product of voltage and current at each instant, or, V*I * cos(phase angle), but...
  23. Replies
    11
    Views
    657

    While the current relay is the "best" method or...

    While the current relay is the "best" method or at least a very good one, the straight timing relay as suggested by Tdegenhart is simple and effective.

    One very good feature is that it limits...
  24. Replies
    6
    Views
    613

    Currents cannot be balanced unloaded because...

    Currents cannot be balanced unloaded because there is no load on the generated leg to draw current...... other than balance capacitors.

    Voltages can only be balanced by using the "balance"...
  25. Replies
    11
    Views
    657

    Because they are harder to buy, and most folks do...

    Because they are harder to buy, and most folks do not want to be modifying relays and testing them. Some of us can do the test and get it right, most probably cannot, or do not want to.

    Agreed it...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4