Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JohnEvans

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thread: Ingo on this

    by JohnEvans
    Replies
    5
    Views
    266

    Pass ! 10 characters

    Pass ! 10 characters
  2. Of the fuel does NOT smell like fresh gas do NOT...

    Of the fuel does NOT smell like fresh gas do NOT run the truck on it. Sour fuel will form gum on the valve stems and when engine cools will stick the valves. Crank it over and bent valves and push...
  3. Spindle speeder from the looks of it.

    Spindle speeder from the looks of it.
  4. Replies
    65
    Views
    3,854

    Rule one of buying machine tool parts ! Be...

    Rule one of buying machine tool parts !
    Be happy you can get the part ,pay the price and live with it. Or Make it!
    Rule 2 -10 as above!!
  5. Replies
    11
    Views
    528

    Yes to low oil with pump sucking air. Figure out...

    Yes to low oil with pump sucking air. Figure out how to check oil level and add if needed . If pump is not submerged below the oil level supply pipe [or whatever] may be allowing air leakage on...
  6. Replies
    11
    Views
    528

    Wrong oil -foaming ,over full ,drain from bearing...

    Wrong oil -foaming ,over full ,drain from bearing restricted/plugged.
  7. Replies
    8
    Views
    597

    PASS ! That looks to be a "Production" lathe set...

    PASS ! That looks to be a "Production" lathe set up to run the same part for a long period. Among other things don't see a reasonably quick/easy way to vary the spindle speed. No power feed of the...
  8. Realistically you will have a better chance of...

    Realistically you will have a better chance of wining the lottery ! Those Taiwan and China made lathes had many detail differences depending on which factory AND time frame when made even from the...
  9. Replies
    23
    Views
    2,212

    Cross slide/compound appear to be off the lathe...

    Cross slide/compound appear to be off the lathe in the background. That lathe has threaded spindle and 3 phase unless someone repowered it. The vari speed drive on these are a bit noisy especialy...
  10. Replies
    10
    Views
    617

    Break out the oxy/acy torch and heat it up near...

    Break out the oxy/acy torch and heat it up near the spindle several times. As said earlier make something that will bolt on 2-3 holes on outer area of the chuck and lock the spindle .Make the arm on...
  11. Replies
    12
    Views
    644

    How about double sided tape,or like I did in HS...

    How about double sided tape,or like I did in HS wood shop turning bowls white glue with a sheet of newspaper between work and backing. That small and thin a few drops on each side if the paper should...
  12. Replies
    8
    Views
    525

    Told ya!! LOL It is surprising what machine tool...

    Told ya!! LOL It is surprising what machine tool parts show up on Ebay .
  13. Replies
    8
    Views
    525

    Lesson 1 machine tool parts are pricey !! Try...

    Lesson 1 machine tool parts are pricey !! Try Ebay might be surprised.
  14. Replies
    8
    Views
    525

    Give Jon at H&W a call good chance he has one.

    Give Jon at H&W a call good chance he has one.
  15. Replies
    9
    Views
    601

    Now if you crash you will tear up something...

    Now if you crash you will tear up something rather than a cheap brass pin. It's called a sheer pin for a good reason.
  16. Replies
    3
    Views
    410

    Down load one of the free online manuals and it...

    Down load one of the free online manuals and it will have that info.
  17. Replies
    13
    Views
    880

    You can buy a oilier that is used to lube the...

    You can buy a oilier that is used to lube the table on a BP mill,or do as I did. Use a GOOD pump oil can and thread the end of the spout to take a 1/8 PIPE male adapter to use a regular Zerk grease...
  18. Replies
    9
    Views
    601

    Pull the complicate unit off the table ,as I...

    Pull the complicate unit off the table ,as I recall those used a pin to drive probables sheered.
  19. $1.00 Put a price on it, this is not a auction...

    $1.00 Put a price on it, this is not a auction site.
  20. Replies
    2
    Views
    528

    Taps

    PM Replied to with payment info.
    Thnaks,John
  21. Replies
    2
    Views
    528

    Taps ,large lot mostly number sizes

    SOLD SOLD This is a LARGE lot of taps ! :lol: Mostly smaller sizes ,hand taps ,gun taps , bottoming taps and some pipe. Sizes include...
  22. Replies
    3
    Views
    573

    Fast sale

    I'm going to say this set a record for a quick sale ,2 minutes after I posted the add !!
    Thanks,Mike
  23. Replies
    3
    Views
    573

    STI Heli Coil Taps

    SOLD Bought a big lot of taps recently and in that lot were 35 STI taps . Various mfgs including Heli coil some spiral flute .Sizes include 10/32,1/4-20,1/4-28,5/16-16,5/16-24,3/8-24.lots of the 1/4...
  24. Replies
    11
    Views
    1,139

    Taper Mic spoken for.

    Taper Mic spoken for.
  25. Replies
    1
    Views
    543

    Pinging Joe Michaels

    Joe : Your PM box is full.I posted my mailing addy in the thread about the gear vernier.
    John
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4