Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: as9100d

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    20
    Views
    1,178

    We surface and centerless grind 85d polyurethane...

    We surface and centerless grind 85d polyurethane often. Holds dimension very well. Machining.....never had any luck. Better off making a mold and pouring it....which is what we do.
  2. Thread: B&A Precision

    by as9100d
    Replies
    5,249
    Views
    805,781

    Right hand to clear the tool changer Sent from...

    Right hand to clear the tool changer

    Sent from my Pixel 3 using Tapatalk
  3. Thread: B&A Precision

    by as9100d
    Replies
    5,249
    Views
    805,781

    Just need to add better chip management is all....

    Just need to add better chip management is all. Roughing endmills to powder the chips, high pressure flood coolant with nozzles in the right place to clear out problem chip areas.

    Adding another...
  4. Replies
    88
    Views
    5,551

    So? $60 an hour is still too cheap. Sent from...

    So? $60 an hour is still too cheap.

    Sent from my Pixel 3 using Tapatalk
  5. Replies
    40
    Views
    2,182

    Hire the old anal retentive machinist that isn't...

    Hire the old anal retentive machinist that isn't as fast as the "younger guys"
  6. Replies
    40
    Views
    2,182

    Young would be discrimination. That said I find...

    Young would be discrimination. That said I find late 20s to early 40s are the sweet spot for QC. Everyone gets a chance though!
  7. Thread: B&A Precision

    by as9100d
    Replies
    5,249
    Views
    805,781

    YouTube (https://youtu.be/hkj2J3Udboc)

    YouTube
  8. We had this same issue. Glad to see you found a...

    We had this same issue. Glad to see you found a fix!
  9. Thread: B&A Precision

    by as9100d
    Replies
    5,249
    Views
    805,781

    Not that this is relevant but have you seen that...

    Not that this is relevant but have you seen that midaco 4th axis tombstone table setup where you can use two tombstones and have 1 rotary unit?
  10. Replies
    508
    Views
    33,659

    Good to know. Those studs are fantastic.the bulge...

    Good to know. Those studs are fantastic.the bulge they talk about is real and messes with performance in milling. It's very noticeable on tiny endmill life.
  11. Thread: Big-plus

    by as9100d
    Replies
    16
    Views
    993

    You can use big plus holders in non big plus...

    You can use big plus holders in non big plus spindles and vise versa. We swap holders from the okumas to Haas with no issues at all.

    And the big Kaiser holders really aren't that expensive. Maybe...
  12. Replies
    508
    Views
    33,659

    We only use JM Performance pullstuds. Never had...

    We only use JM Performance pullstuds. Never had one fail and have cut our TIR by almost half in the haas machines using big kaiser tool holders.
  13. Replies
    5
    Views
    520

    Take a look at YG1 YG-1: BEST VALUE IN THE...

    Take a look at YG1

    YG-1: BEST VALUE IN THE WORLD OF CUTTING TOOLS
  14. Replies
    508
    Views
    33,659

    I agree with you and my comment was sarcasm. I...

    I agree with you and my comment was sarcasm. I would be furious as I'm sure you are.
  15. If you need photos or a better explanation, I can...

    If you need photos or a better explanation, I can send photos.
  16. Replies
    508
    Views
    33,659

    Well it is true... They can break.

    Well it is true... They can break.
  17. Thread: Chick One LOC?

    by as9100d
    Replies
    6
    Views
    485

    Yes they repeat

    Yes they repeat
  18. Need to use a dial test indicator to measure the...

    Need to use a dial test indicator to measure the gage length. Zero on the face of the spindle then zero in the control under position. Wheel the Axis up and zero the dti on the bottom face of the...
  19. Thread: Big-plus

    by as9100d
    Replies
    16
    Views
    993

    They are amazing. Big plus holders will fit in a...

    They are amazing. Big plus holders will fit in a non big plus spindle.

    Big plus holders are also amazing.
  20. Drill, mill, file, done.

    Drill, mill, file, done.
  21. If you leveled I'm x and y, you need to go...

    If you leveled I'm x and y, you need to go through the entire probe calibration process.
  22. Replies
    88
    Views
    5,551

    I have always said I base my prices off a price...

    I have always said I base my prices off a price of a Coke.

    Cokes go up, so do my prices... Coke has an entire team to set prices and so far ..it has worked fine for me lol.
  23. If I had to guess, your tool setter pad isn't...

    If I had to guess, your tool setter pad isn't level in both axis.
  24. Replies
    88
    Views
    5,551

    I agree Mike.

    I agree Mike.
  25. Replies
    88
    Views
    5,551

    That's going to be everywhere. We handle that...

    That's going to be everywhere.

    We handle that by having the manager oversee the new hire and check everything often. It's the managers job to take notes of what they lack in so when we do the 90...
Results 1 to 25 of 368
Page 1 of 15 1 2 3 4