Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Jeffers1

Search: Search took 0.00 seconds.

  1. In Kenosha vs Milw. Try Dan at DC Design...

    In Kenosha vs Milw. Try Dan at DC Design 262-652-6281. He stands behind his work and is a real straight shooter..
  2. RJT, Yes and I did try the original setup that...

    RJT,
    Yes and I did try the original setup that way too and it didn't seem to make a difference..
  3. Yes, the profilometer repeats on a flat surface...

    Yes, the profilometer repeats on a flat surface and too is accurate to the test plate.. FWIW we just happened to have our annual calibration circus and the profilometer got a pass... I think the...
  4. Replies
    12
    Views
    3,150

    Would an M0 or use of OP STOP with an M01 instead...

    Would an M0 or use of OP STOP with an M01 instead of the M30 do the trick for you?
  5. The ht. stand attachment is our typical setup...

    The ht. stand attachment is our typical setup too, but with the smaller Ø its so important to get the probe aligned and centered with the bore in question, I was certain this setup would be...
  6. Saw that bracket this morning on the Mahr site as...

    Saw that bracket this morning on the Mahr site as well, its good to know for future reference. The pocket surf is attached with 2 mitee-bite clamps.
  7. Not a bad idea, so I tried it results were;...

    Not a bad idea, so I tried it results were; 19,20,30,63 in that order. That was attaching taking a reading, then loosen resnug and repeat 4x. The new plan is to machine this design into a larger...
  8. Best procedure Profilometer usage? made a "jig"... did'nt work as planned...

    6113661137611386113961140Looking for advice, need to verify a 16ra (in) finish at a 1.125" Ø bore. Feel really good about the process and yield acceptable parts. Problem is it usually times takes...
  9. Replies
    6
    Views
    1,918

    Update, to "breakdown" this machine and replace...

    Update, to "breakdown" this machine and replace the seals a set of holes were drilled and tapped to lift the "outer ring" unfortunately the drill tip broke thru causing the leak after the seals were...
  10. Replies
    2
    Views
    3,882

    I would get a hold of salesmen for komet or the...

    I would get a hold of salesmen for komet or the like with the replaceable head style reamers, seems most every popular brand has one now and with your tool life already known and parameters given I...
  11. Replies
    6
    Views
    4,835

    Compact flash is the way to go, I don't know that...

    Compact flash is the way to go, I don't know that 1GB will work, I know I bought a 4GB thinking bigger is better then found it would'nt work (apparently too big). I think a 32 or 64 MB is what was...
  12. Replies
    14
    Views
    3,532

    yes, by Onecnc

    yes, by Onecnc
  13. Replies
    14
    Views
    3,532

    I loaded NClink Free from internet a few months...

    I loaded NClink Free from internet a few months ago and was super easy to setup and use, just need a PC and RS232 cable near. Google NCLink Free. Also works as an editor..
    good luck
    Jeff

    ps
    we...
  14. Replies
    12
    Views
    25,464

    I can relate to Toyoda's poor service and...

    I can relate to Toyoda's poor service and response, it seems they have 2 awesome Techs and your lucky to get either of them on the phone even though you pay the same $130 an hour for phone service...
  15. Replies
    6
    Views
    1,918

    Definately hyd. oil leaking excessively (about a...

    Definately hyd. oil leaking excessively (about a gallon every 10 hrs) sitting idle. The Hydraulics clamp the table after a pallet change, and raise and lower the curvic coupling before and after...
  16. Replies
    6
    Views
    1,918

    How much hydrailic pressure is too much?

    Hi all, been reading in PM for a while and finally decided it is time to join and contribute and absorb. My question as of lately is in regards to the Hyd. Pump pressure on our Mori Seiki MH500. A...
Results 1 to 16 of 16