Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: GENERALDISARRAY

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    20
    Views
    1,266

    What is the motor part number What is the part...

    What is the motor part number

    What is the part number of this magnetic pulse coder you were looking for?
  2. Replies
    6
    Views
    394

    line to line you have 235+ volts? so 240 three...

    line to line you have 235+ volts? so 240 three phase?
  3. Replies
    5
    Views
    284

    It will do both (the OTS) and no, never

    It will do both (the OTS)

    and

    no, never
  4. Replies
    40
    Views
    2,183

    You can see how the original "secure ig unit" was...

    You can see how the original "secure ig unit" was put together in the original door. It was made just how Emanuelgoldenstein says.

    I have only had to mess with them because a tap broke and a piece...
  5. Replies
    3
    Views
    420

    Its all in 50lb Sandvik boxes of inserts and...

    Its all in 50lb Sandvik boxes of inserts and endmills, sorted by such.

    They were the first company to respond,Thanks for the recommendation.
  6. Replies
    3
    Views
    420

    carbide recycling

    I have only ever dealt with Sandvik recycling in the past. but recently they wont return an email.

    I have received a quote of 8.75-9 a pound from two of the four recyclers I have contacted.
    ...
  7. Replies
    2
    Views
    404

    Im not familiar with a 0imate, and you dont say...

    Im not familiar with a 0imate, and you dont say what version (A,B,C), I wouldnt lose hope.

    The right guy can look at the ladder and figure out keep relays and data tables that are used and might...
  8. The finish on the wall or the finish on the...

    The finish on the wall or the finish on the floor?

    Is the material in the pre-hard or annealed condition?
  9. Replies
    16
    Views
    966

    What does Tsugami say? I would want a...

    What does Tsugami say?

    I would want a guarantee of performance/ turn-key on a deal like that.

    How are you going to measure it?
  10. Not to hijack but Why cant I write to #7021...

    Not to hijack
    but

    Why cant I write to #7021 and above if I can read from #7001 through 8. Yields alarm 115.

    18i M maybe model B. Its around a ~98-99

    work around is G10L20P3 Y#7002
  11. You say budget is not an issue, For...

    You say budget is not an issue,

    For prototyping it would be a Baxis subspindle Integrex type machine hands down. Trying to squeeze 14 driven tools onto a 12 station turret sucks. Especially for...
  12. Replies
    30
    Views
    1,614

    Since doing it the right/efficient way is a no...

    Since doing it the right/efficient way is a no go. And not knowing at all what the part looks like.

    You can drill the hole first, then establish the OD concentric to the drilled wonky hole. Which...
  13. Replies
    20
    Views
    1,266

    You said you had the drive repaired, by whom? ...

    You said you had the drive repaired, by whom? Did they run it on a test stand?

    AL29 is not a spindle amp related alarm, as you said it had earlier.

    The sensor inside the motor back to the amp...
  14. Replies
    20
    Views
    1,266

    https://www.mroelectric.com/static/application/pro...

    https://www.mroelectric.com/static/application/product/pdfs/b65165e.pdf

    https://www.gefanuc-spares.com/fanucalphamanual.pdf
  15. Replies
    20
    Views
    1,266

    There is no magic inside the spindle motor. It is...

    There is no magic inside the spindle motor. It is like any other 3 phase induction motor.With a sensor on it.

    The drive should have a led display on it. what does it say when it is alarmed? 8....
  16. Replies
    7
    Views
    676

    That is exactly what that alarm means. You are...

    That is exactly what that alarm means.

    You are going to have to go faster to "get on the pipe" like S1000
    Dont forget G94 when your done !
  17. Replies
    9
    Views
    807

    I run almost twice that SFM in 316SS.

    I run almost twice that SFM in 316SS.
  18. Your gonna mess up the teflon. Like Fred said,...

    Your gonna mess up the teflon.

    Like Fred said, disassemble in situ.
  19. So whenever you setup a new part, you have to set...

    So whenever you setup a new part, you have to set every tool you are going to use? Even if they are always in the magazine?

    Very productive.
  20. usually the hose from the pump connects to the...

    usually the hose from the pump connects to the wheel nozzle through a slip joint arrangement. You grab the hose end and pull up to detach it. Then you have a little nozzle with a valve you can wash...
  21. Replies
    9
    Views
    818

    Get a whole plate, Your quoting a odd size,...

    Get a whole plate,

    Your quoting a odd size, maybe they are putting processing/sawing on the per pound price.
  22. That looks like fun, how do you go about getting...

    That looks like fun, how do you go about getting jobs like that?
  23. Replies
    2
    Views
    307

    swiss collet spring

    Anyone know where to buy these volute springs that go between the collet and sleeve?
  24. I have a 32i and 0iF non-plus lathes here. They...

    I have a 32i and 0iF non-plus lathes here. They all have three digits on the tool offset pages. We dont do anything different.

    On a control that new, I think Fanuc factory support should be all...
  25. Replies
    5
    Views
    822

    It was indeed a CNC softwares fine, not the...

    It was indeed a CNC softwares fine, not the reseller. They lowered the Bad Dog Fee to 500.

    My maintenance expired on 10/31/20
Results 1 to 25 of 405
Page 1 of 17 1 2 3 4