Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Drroaster

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    21
    Views
    1,937

    Nice YouTube on our discussion

    Nice YouTube on our discussion
  2. Replies
    21
    Views
    1,937

    264975 This is the paragraph from the 508a...

    264975
    This is the paragraph from the 508a requirements/I referred to-
  3. Replies
    21
    Views
    1,937

    What machine did you get for cutting and...

    What machine did you get for cutting and stripping? The ferrules that I use (Wago) has a ferrule that is designed for 2 wires great for my strain gauges where we have a jumper wire.
  4. Replies
    21
    Views
    1,937

    The 508A only states that ferrules have to use a...

    The 508A only states that ferrules have to use a crisper approved by ferrule manufacturers. Also for reasons unknown they do not allow for use of ferrules on existing equipment in the field
  5. 264806264806 This is what I have brand new yours...

    264806264806
    This is what I have brand new yours if you want it
  6. Australia uses 415 3 phase no low / high I have a...

    Australia uses 415 3 phase no low / high I have a couple of vfd’s I will look to see if they use single phase if so I will give it to you you pay shipping
    Boyd
  7. Replies
    5
    Views
    739

    YouTube...

    YouTube

    Found this on YouTube that I thought about when my mx2 goes away
  8. Replies
    6
    Views
    1,033

    Not to hijack but would your manual be for a...

    Not to hijack but would your manual be for a diacro 14/48-2? That is what I have and have been looking for a manual. If so could I bother you for a copy? Thank you in advance
    Boyd
  9. Replies
    45
    Views
    9,006

    Most of the damage to the burrs comes from the...

    Most of the damage to the burrs comes from the material found in coffee rocks nails wood. As coffee is dried on cement patios and raked then when it’s dry to proper moisture it’s shipped. Roaster can...
  10. Replies
    389
    Views
    50,464

    Thank you for your help

    Thank you for your help
  11. Replies
    389
    Views
    50,464

    Adam thank you for your help on this forum. I...

    Adam thank you for your help on this forum.
    I am using a mac for my co. I have a programmer who wanted me to use the mac for our plc system. Well long story short I use Autocad inventor 12 and my...
  12. Replies
    13
    Views
    2,067

    Call B&b electronics Industrial Device Networking...

    Call B&b electronics Industrial Device Networking - Serial, Ethernet & USB - B&B Electronics tell them what your doing and it's done
  13. SWI told me to go into setup and reset 0 and...

    SWI told me to go into setup and reset 0 and span. Span had to be better than 3"
  14. Along those same lines The reason Jaguar never...

    Along those same lines
    The reason Jaguar never made tv's
    Couldn't figure out how to make them leak oil
  15. Replies
    29
    Views
    2,555

    Also good to note when electronics are on a 3...

    Also good to note when electronics are on a 3 phase setup make sure the power supply is NOT the generated third leg
  16. Replies
    29
    Views
    2,555

    I have a 250 amp panel in my shop then added a 15...

    I have a 250 amp panel in my shop then added a 15 hp rotophase with a 60 amp breaker ran 3/4 conduit through the side of the shop that needed the 3- phase in each conduit I ran two circuits (remember...
  17. Replies
    57
    Views
    8,485

    Well when your in the people's republic of...

    Well when your in the people's republic of California you will. It's amazing how as far as public and media goes a guy with a squirt gun is dangerous. Yet when a gang member shoots it's news and he's...
  18. Replies
    57
    Views
    8,485

    Happen to me as well police came out and got good...

    Happen to me as well police came out and got good set of finger prints but that is as good as it got there only comment was hope you have insurance. Go and call them telling them someone just broke...
  19. Replies
    7
    Views
    3,307

    You could look up Dave brown he comes across them...

    You could look up Dave brown he comes across them quite regularly.
    B
  20. Replies
    47
    Views
    9,014

    If it is setting for a while between firing it is...

    If it is setting for a while between firing it is probably leaking enough to fire up but not enough to run. If it still won't fire with power applied bypass it for a test.
  21. Got it thanks for taking the time to explaine it...

    Got it thanks for taking the time to explaine it for me
  22. Do I remove the set screws or just count? I have...

    Do I remove the set screws or just count? I have 11 pieces to do but this was the reason I bought the indexer for. Thanks for the help
    Boyd
  23. Thanks to Jim and mike for this. Is there...

    Thanks to Jim and mike for this. Is there anything out there on thought process of how to set it up? I will be using it to do 3 holes in a cylinder. I started at 0 and marked every line with a 3 on...
  24. Replies
    7
    Views
    1,532

    Great news congrats Dave

    Great news congrats Dave
  25. Replies
    22
    Views
    3,615

    I own both of my tanks, both are 500 gal. If you...

    I own both of my tanks, both are 500 gal. If you rent the tank you have to buy the propane from the tank owner, he will be happy to charge you about 25 % higher price to fill a rented tank. If you...
Results 1 to 25 of 105
Page 1 of 5 1 2 3 4