Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Captain Dan

Search: Search took 0.00 seconds.

  1. Thanks for that info. Dan

    Thanks for that info.
    Dan
  2. Thanks for the info. Question: Doesn't having...

    Thanks for the info.
    Question: Doesn't having the Emory paper grit towards the steady rest cause wear of the clamp fingers, even with the paper oiled?
  3. South Bend steady rest with rollers on tips

    Hi,
    Was just using my 10k steady rest today.
    Worked ok, but wondered if anyone had added ball bearings to the tips so that marks would not left on round part being machined.
    If so, do the ball...
  4. Replies
    2,269
    Views
    439,054

    Sticky: Hi, I have a new (to me) SB 10K lathe. ...

    Hi,

    I have a new (to me) SB 10K lathe.

    Model # CL670Z
    Serial # 40954 K
    This was purchased new by the previous owner in the late 1980's, do not know the exact date.
    My lathe has a "Built...
  5. Replies
    5
    Views
    1,270

    I don't know if this thread still has any one...

    I don't know if this thread still has any one monitoring it, but I had the same problem.
    The fix is to carefully take off the crank. It will have a 1/8" round key keeping the crank handle from...
  6. Replies
    8
    Views
    673

    Thanks, I forgot to mention that I have standard...

    Thanks, I forgot to mention that I have standard hand wheel drawbars.
    Dan
  7. Replies
    8
    Views
    673

    Ok. Thanks for the confirmation. The 3MT seems...

    Ok. Thanks for the confirmation.
    The 3MT seems to fit correctly, but there seems to be max confusion on the forum about the taper in a 10k lathe. I just needed to be sure.
    I'll spend some time...
  8. Replies
    8
    Views
    673

    10k spindle question

    Over the years this question must have been asked many times, but the search function did not serve me well-or more likely, I asked the wrong question.

    I have a late model 10k without any...
  9. Replies
    4
    Views
    605

    Well, I discovered the binding problem, and not...

    Well, I discovered the binding problem, and not what I thought.
    When I got the handle off I looked at the graduated collar and put it on a flat surface. No problem there. Put it back together again...
  10. Replies
    4
    Views
    605

    Thanks for the info. Dan

    Thanks for the info.
    Dan
  11. Replies
    4
    Views
    605

    10K compound handle removal

    Hi,

    I have a binding in the compound that I am pretty sure is caused by the large 0-200 graduated collar. If you loosen the thumb screw the compound lead screw works smoothly. If you tighten up...
  12. Replies
    11
    Views
    1,174

    mandmj' Thanks for that picture. It is obvious...

    mandmj'
    Thanks for that picture. It is obvious that my 10K is standard for an 80's model.
    I was just curious.
    Dan
  13. Replies
    11
    Views
    1,174

    On my lathe, I pull the handle to tension the...

    On my lathe, I pull the handle to tension the belt. Oh well, it works fine, so I won't mention it again. Now, on to finishing the new tool post.
    Dan
  14. Replies
    11
    Views
    1,174

    Hi, I'll try to do pictures via DropBox. ...

    Hi,
    I'll try to do pictures via DropBox.

    Dropbox - Picture of belt tensioner1.jpg - Simplify your life

    Dropbox - Picture of belt tensioner2.jpg - Simplify your life

    Dropbox - 10K lathe.jpg...
  15. Replies
    11
    Views
    1,174

    New to me 10K lathe

    Hi,

    I just joined this forum. I have used a Taig lathe and just sold my 9x20 Jet lathe that I had for years.
    I purchased a 10k lathe that was a one owner, only driven on Sunday and always...
Results 1 to 15 of 15