Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Luke.kerbey

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    112

    Hi, Thanks for that explanation, was easy to...

    Hi,

    Thanks for that explanation, was easy to understand, so does this mean that the seal may not need replacing? And this binding that is occurring, will it cause the bearing to need replacing? Or...
  2. Replies
    2
    Views
    112

    Jones and shipman universal grinder

    Has anyone got advice on how much damage is caused in our wheelhead?

    I switched on the machine last week and the wheel stalled after a couple minutes and the motor cut out, noticed the oil had...
  3. Have you got the right tool holders? We had a...

    Have you got the right tool holders?

    We had a similar problem when I started using a different set of tool holders on a TRAK knee mill, except the draw bar was too short, so we made a longer one.
  4. Replies
    3
    Views
    390

    If you can find a buyer why not?

    If you can find a buyer why not?
  5. Replies
    0
    Views
    217

    Hurco 900 generator wonít stay on

    Hi guys,

    Got a hurco 900 with 50/10 amp generator.

    Yesterday it was running all good and then a transistor blew which was shown by the transistor blown light. But because it was the prime 0.2...
  6. Replies
    6
    Views
    793

    My first mentor used to poor his cold milky tea...

    My first mentor used to poor his cold milky tea in the coolant. It used to develop this skin that was science experiment level.
  7. Replies
    11
    Views
    1,055

    Okay cool, there should be a combination of parts...

    Okay cool, there should be a combination of parts and adapters so you can mount the magnetic head on to the machine head. Then the chuck sticks to the magnet. Iím assuming the magnetic chuck has the...
  8. Replies
    11
    Views
    1,055

    You need a current 3R catalogue. They havenít...

    You need a current 3R catalogue. They havenít changed much in 40 years and all new gear is compatible with old.

    What systems do you have? 20mm diameter stems? Macro pallets?

    The mounting can...
  9. Replies
    12
    Views
    1,092

    The Agie form you speak of is actually two...

    The Agie form you speak of is actually two different machines. It used to be Agie and charmilles were different brands altogether but were bought by +GF+. The form 350 is most likely closely...
  10. Replies
    5
    Views
    658

    Chuck it in a 4 jaw independent or a face plate...

    Chuck it in a 4 jaw independent or a face plate if possible
  11. Replies
    6
    Views
    693

    Hi, If the user interface is similar to the...

    Hi,

    If the user interface is similar to the mondo, you can move the cursor to the top left corner to highlight the page number, then by pressing numbers 4 through 9 (press enter after each...
  12. Replies
    6
    Views
    693

    Is it a mondo or a mondo star? Or am I...

    Is it a mondo or a mondo star?

    Or am I thinking of the wrong machine?
  13. Replies
    2
    Views
    625

    All the machines Iíve used, the surface area that...

    All the machines Iíve used, the surface area that you give the machine is the size of the frontal electrode face. Usually in CM squared. Not the cavity size

    I take it your running a Agie machine...
  14. Replies
    5
    Views
    1,038

    The major thing about knee mills wearing out is...

    The major thing about knee mills wearing out is how the knee drops forward over time. This run out is common wear but unless you can tighten the gibs on the table height without it going tight at...
  15. Replies
    9
    Views
    580

    No, the story is that the machine has been like...

    No, the story is that the machine has been like this for atleast 10 years (Iíve been there for 1 year) and anyone who has used it has just accepted that the machine doesnít grind properly flat and...
  16. Replies
    9
    Views
    580

    See the duplicated thread in the abrasive forum,...

    See the duplicated thread in the abrasive forum, it has the photos of the ram thatís bent, it works in manual fine, when the ram is detached and then run full travel , both ways it mimics what...
  17. Replies
    9
    Views
    580

    I checked all that, the rod for the cross feed...

    I checked all that, the rod for the cross feed cylinder is bent and is getting stuck in the cylinder piston and bush and possible pulling tight the saddle on to the slide, I only found this out by...
  18. Replies
    63
    Views
    4,359

    Bore out, double key and sleeve and re cut the...

    Bore out, double key and sleeve and re cut the key in the same position.

    Itís easily done, I used to bore and key sets of sprockets that were used in gangs on shafts where all the teeth had to...
  19. Replies
    7
    Views
    822

    Colchester, all day long!

    Colchester, all day long!
  20. Replies
    2
    Views
    776

    Cheers for the reply, in the end I found the...

    Cheers for the reply, in the end I found the manual and set it up,
    after being told that it didnít work, and getting the whole war and peace about how the guy who fixed it is useless.... there was...
  21. Replies
    8
    Views
    1,569

    Hi, Yes this situation is quite predictable,...

    Hi,

    Yes this situation is quite predictable, I should of given a background first.
    We are a toolroom of 6 guys which is part of a injection mould factory. We maintain old tools, build some of...
  22. Replies
    8
    Views
    1,569

    Toolroom/ Machine shop tier boards

    The management want us in the tool room to produce a big white board on the wall style chart that easily shows the management what the toolroom work flow is looking like. They said it must be

    -...
  23. Replies
    7
    Views
    1,167

    How long did they last though?

    How long did they last though?
  24. Replies
    14
    Views
    1,419

    Do any of the diamond veterans know if there is...

    Do any of the diamond veterans know if there is different types or grades of dressing diamonds? I use the typical diamond on a block to flat dress but also those small triangle ones that are used in...
  25. Replies
    7
    Views
    1,006

    Makes perfect sense, Although if you run a...

    Makes perfect sense,
    Although if you run a charmilles itís far easier just to run the guide setup cycle 👍🏼
Results 1 to 25 of 125
Page 1 of 5 1 2 3 4