Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: HTP Machine

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    814

    VTM- thank you you hit it right on the spot. I...

    VTM- thank you you hit it right on the spot. I have turned machine on several times, After homing machine and MDI high gear and a spindle, pushed button to advance the quill, then MDIíd M26 as you...
  2. Replies
    8
    Views
    740

    I have checked all the switches on the Q-setter...

    I have checked all the switches on the Q-setter and all are good. Anybody know of anything else I can check to get the Q-setter to work?
  3. Replies
    9
    Views
    814

    I donít see any switches or toggle switches...

    I donít see any switches or toggle switches anywhere for the tailstock either
  4. Replies
    9
    Views
    814

    Sorry I donít know how to get a copy of my...

    Sorry I donít know how to get a copy of my picture of the control and paste it here. Any suggestions.
  5. Replies
    9
    Views
    814

    Yes I have tried after start up advancing and...

    Yes I have tried after start up advancing and retracting quill and holding it each way for 5 to 10 seconds
  6. Replies
    9
    Views
    814

    Hitachi Seiki HT20 Quill Problem

    Hitachi Seiki HT20 with Fanuc 10TF having problem with quill since I bought machine last year. With the quill on tailstock in the in position spindle will not start up. With the quill in out position...
  7. Replies
    8
    Views
    740

    No message on alarm, just the red alarm on. And...

    No message on alarm, just the red alarm on. And all switches for the pods check good on the ladder. Would there be a parameter that could be adjusted to set the q-setter ?
  8. Replies
    8
    Views
    740

    Yes it worked before I lost the parameters due to...

    Yes it worked before I lost the parameters due to the batteries went dead. I cleaned around q-setter and no chips in the way. The alarm goes off as soon as q-setter is disengage from home.
  9. Replies
    8
    Views
    740

    Hitachi Seiki HT20 Q-Setter Alarm

    After reloading parameters on Hitachi Seiki HT20 with Fanuc 10TF control, now when I pull the Q-Setter down to touch off tools I get an alarm with no message. Put it back up in it home position and...
  10. Found problem sorry so late to update. The ribbon...

    Found problem sorry so late to update. The ribbon cable in monitor cabinet that runs from keyboard to back of cabinet to board had a bad worn spot where it had been laying across a metal frame in the...
  11. Replies
    7
    Views
    656

    Alarm fixed finally, the proximity sensor I was...

    Alarm fixed finally, the proximity sensor I was given was wrong sensor, I have installed the correct proximity sensor and now machine starts up with no alarm and is up and running.
  12. Replies
    7
    Views
    656

    The clutches are monitored by a proximity sensor....

    The clutches are monitored by a proximity sensor. The one on Z axis had bad wiring so I changed it out, but still have same alarm.
  13. Replies
    7
    Views
    656

    By any chance would you know which card or which...

    By any chance would you know which card or which board I need to look at would you?
  14. Replies
    7
    Views
    656

    Thanks, I donít even see any switches or wires...

    Thanks, I donít even see any switches or wires that run to the clutch. Iíll have to figure out which I/O card relates to the clutches. Iíll be checking
  15. Replies
    7
    Views
    656

    Also I just looked in the dyonastic page X001 it...

    Also I just looked in the dyonastic page X001 it shows a 1 on bit 4, and on X003 it shows 0 on but 7.
    So the X clutch shows engaged
    And the Z clutch shows not engaged, but manually checked and it...
  16. Replies
    7
    Views
    656

    Hitachi Seiki HT20 alarm on power up

    Need help please, I have a Hitachi Seiki HT20 with Fanuc 10TF control. Machine was running great, went to power up machine and now I get a red alarm light and EMG highlighted on the bottom of the...
  17. I checked all fuses and breakers and all are...

    I checked all fuses and breakers and all are good, there is no power going to the power supply board by the motherboard and no power to the power supply board underneath the monitor.
  18. It is a Hitachi Seiki HT20 Lathe with Fanuc 10TF...

    It is a Hitachi Seiki HT20 Lathe with Fanuc 10TF control, I think 1988 Model.
  19. Hitachi Seiki CNC Lathe control does not start up

    Cold outside and cold in shop, went to start Hitachi Seiki CNC Lathe and control panel does not start when I push the green start button. Machine ran just fine last night. I donít keep my shop heated...
  20. Replies
    14
    Views
    986

    I am in the process of checking out the EcoCut...

    I am in the process of checking out the EcoCut tool, thanks for the info on this tool.
  21. Replies
    14
    Views
    986

    Using an insert drill would be ok but the...

    Using an insert drill would be ok but the deafening squealing that can be heard a block away would probably irritate other tenants in my area. Iíll try this insertable dril but any way to dial the...
  22. Replies
    14
    Views
    986

    Ok thanks for the info

    Ok thanks for the info
  23. Replies
    14
    Views
    986

    Wished I had high pressure coolant but I donít ...

    Wished I had high pressure coolant but I donít
    So like a DFT style insert drill would work well?
  24. Replies
    14
    Views
    986

    Drilling N50 HS Steel

    Anybody have a good way to drill N50 HS Steel? I have a Hitachi Seiki HT20 CNC Lathe with 15 hp motor. Having problems drilling 1inch diameter hole X 1.250 deep.
    What would be a good type drill for...
Results 1 to 24 of 24