Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Mram10

Page 1 of 14 1 2 3 4

Search: Search took 0.00 seconds.

  1. I use Pins in the muzzle and chamber area. In my...

    I use Pins in the muzzle and chamber area. In my experience, it doesn’t have to be .000000001” tir to shoot well. I have a test barrel 300rum done in a 3 jaw with around .007” tir that shoots the...
  2. 1960s was the start of the large statistical...

    1960s was the start of the large statistical increase in homicides and illegitimate children. Primary variables were removing God from schools and the Free Love movement. Teach a kid they are an...
  3. Thread: jonnonow

    by Mram10
    Replies
    7
    Views
    3,967

    He got sick of the know it alls on the forums...

    He got sick of the know it alls on the forums that go against real experience. Can’t blame him. I’m sure you understand that very well Butch....
  4. Simple solution: point out statistics that show...

    Simple solution: point out statistics that show majority of gun deaths are suicide or gang related. Other than that, be ready to fight for your rights. Sad thing is only a handful of guys were...
  5. Replies
    80
    Views
    4,102

    Logic based fixes WOULD work. Death penalty rids...

    Logic based fixes WOULD work. Death penalty rids society of violent offenders and their 90% recidivism rate. That’s cuts crime in half. Remove alcohol from the shelves and that would greatly reduce...
  6. Replies
    17
    Views
    1,501

    I’m shocked the Rem required that much! I’ve...

    I’m shocked the Rem required that much! I’ve trued up a bunch of newer ones and haven’t needed more than a couple thousandths to square the receiver face
  7. Replies
    86
    Views
    12,950

    I used sched80 pvc in the wall snaked up and down...

    I used sched80 pvc in the wall snaked up and down with 2 valves at the bottoms of the snakes for water traps. Worked for the last 8 years and very cheap. Kind like this setup but in the wall.
    261439
  8. Replies
    8
    Views
    786

    Prep is definitely everything. Baked on cerakote...

    Prep is definitely everything. Baked on cerakote has given me much better results than polane, Durakote and other air drying types. Basics for me:
    Sand barreled action with 400grit ao on palm sander...
  9. Replies
    16
    Views
    1,998

    Trying to find an alternative to fireforming...

    Trying to find an alternative to fireforming since I don’t always have time to run to the range. Nice to go into the shop at midnight when you can sleep and knock out some cases.
  10. Replies
    8
    Views
    786

    Never had any bubbles and the manufacturer...

    Never had any bubbles and the manufacturer recommends both ways.
  11. Replies
    8
    Views
    1,588

    Have you considered electro etching since your...

    Have you considered electro etching since your volume is low?
  12. Replies
    8
    Views
    786

    300 for 1 hour on metal parts. Google cerakote...

    300 for 1 hour on metal parts. Google cerakote application
  13. Replies
    17
    Views
    1,501

    I’ve built 2 tikkas and the 1-16” worked for...

    I’ve built 2 tikkas and the 1-16” worked for them. Not older actions
  14. Replies
    43
    Views
    34,357

    My eisen was on sale for $3800 and has built...

    My eisen was on sale for $3800 and has built plenty of accurate long range rifles. I don’t know of any for under $3k though. Good luck.
  15. Replies
    31
    Views
    2,740

    You have to stop showing your ignorance, mib....

    You have to stop showing your ignorance, mib. Watch my video and you’ll see I know what I’m talking about. I’m sure you’re after the truth and not just being a jack wagon.
    Love the pink and orange...
  16. Replies
    17
    Views
    1,501

    Tikka, maybe??? Can’t remember the length, but...

    Tikka, maybe??? Can’t remember the length, but threads and diameter make sense
  17. Replies
    16
    Views
    1,998

    .460” at shoulder to case sides.

    .460” at shoulder to case sides.
  18. Replies
    16
    Views
    1,998

    Noise in the shop. Trying something new....

    Noise in the shop. Trying something new. Curiosity.
  19. Replies
    31
    Views
    2,740

    Watch my videos about electro etching with...

    Watch my videos about electro etching with vinegar and salt. See how I don’t know what I’m talking about. Glad I’m so important to you that you feel you have to respond to my every post.
  20. Replies
    31
    Views
    2,740

    I acid etch with vinegar/salt and a battery...

    I acid etch with vinegar/salt and a battery charger
  21. Replies
    16
    Views
    1,998

    Thanks. I’ll look into it

    Thanks. I’ll look into it
  22. Replies
    16
    Views
    1,998

    Not sure exactly. Primarily a die that will help...

    Not sure exactly. Primarily a die that will help turn 308 into 7-08ai by feeding a round into my rock chucker and using hydraulic pressure to form the ai portion of the round. Basic is good. Other...
  23. Replies
    16
    Views
    1,998

    Still crabby as ever, I see. I’m actually feeling...

    Still crabby as ever, I see. I’m actually feeling sorry for you ... I only offer advice when I have experience, but thanks.
  24. Replies
    16
    Views
    1,998

    Thanks Danny.

    Thanks Danny.
  25. Replies
    50
    Views
    6,979

    Ignorance? Do I know you bottomfeeder? Or, low...

    Ignorance? Do I know you bottomfeeder? Or, low flier...
Results 1 to 25 of 331
Page 1 of 14 1 2 3 4