Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: texasgunsmith

Page 1 of 55 1 2 3 4

Search: Search took 0.03 seconds.

  1. I have already leveled the bed, as you can see in...

    I have already leveled the bed, as you can see in the previous posts. So the objective with the test bar is to get the spindle parallel to the ways on both a horizontal plane and vertical plane. This...
  2. Ready to start running checks with the test bar....

    Ready to start running checks with the test bar. The test bar fits into the taper of the spindle. The spindle taper is a proprietary taper known as Special South Bend 3 Morse taper. Pretty sure its...
  3. Replies
    1
    Views
    86

    Email Ted with parts needed: [email protected] ...

    Email Ted with parts needed:
    [email protected]

    Or ebay.
  4. Replies
    24
    Views
    799

    Aloris is an excellent USA made product. Each...

    Aloris is an excellent USA made product. Each model goes up in size per swing of lathe. Generally like axa, bxa, cxa, then ca, and da.

    I use a CA. Kevin T uses a CXA and needed to add a plate on...
  5. Replies
    24
    Views
    799

    Your lathe is from 1947. That style serial...

    Your lathe is from 1947. That style serial started that year, that's why there are only 4 digits before the letters. Info here:
    South Bend Lathe Co.

    Serial number list here, scroll to 1947. You...
  6. Replies
    24
    Views
    799

    With those spindle caps you have copper bearings....

    With those spindle caps you have copper bearings. The two set screws in the middle of the cap have to do with bearing adjustment. Don't remove cap without easing that adjustment, I believe. Also...
  7. For a little update. I let it sit overnight with...

    For a little update. I let it sit overnight with the weight on it. In that short time it pulled in a little bit. I'd call it about .00075" out on tail stock end now.

    Checking level both ways:
    ...
  8. 302847 302848

    302847 302848
  9. Fine tuning the leveling of tail stock end was a...

    Fine tuning the leveling of tail stock end was a bit trickier. Less weight on that end. This is where using bolts or studs driven into the concrete would help. You could force any bed twist out in...
  10. Replies
    24
    Views
    799

    $1250 is like a wild weekend at the bar ! :D ...

    $1250 is like a wild weekend at the bar ! :D

    Now you have not just a tool, but a Made in the USA machine. Investing in your future and family. Maybe your wife will like that explanation ! :D
    ...
  11. $426000 sounds like city center prices, or...

    $426000 sounds like city center prices, or outlying areas with some acreage. That price is generally upper middle class in a pretty decent suburb, though they can range from let's say $280k to...
  12. Replies
    24
    Views
    799

    A little more light reading. :D In another...

    A little more light reading. :D

    In another thread I linked a short list of 16" threads that guys overhauled or went through a bit. You can see that list here:
    New guy with new lathe
  13. Replies
    24
    Views
    799

    We feast on pics and updates, like Gollum needs...

    We feast on pics and updates, like Gollum needs his ring :D. So keep posting with updates and pics.

    If you give the serial number, on flat way, tail stock end we can tell which year it is. Based...
  14. Yea, its pretty tight. I was being lazy in...

    Yea, its pretty tight. I was being lazy in description :D, just giving everyone a rough idea. That's why I said "what I'm calling. . ." But no joke, probably spent 2 hours adjusting levels, a c hair...
  15. I have previously adjusted both my levels. Having...

    I have previously adjusted both my levels. Having got them dialed in as far as I'm willing to spend time with them :D. You could make a lifetime career of trying to get dead zero on them. I got both...
  16. Those are excellent, and the 1/2" thread would be...

    Those are excellent, and the 1/2" thread would be a perfect fit for my 16's. Might opt for that on my other 16".

    This is a lathe I need to sell though. As it is, I expect I might break even on...
  17. Replies
    11
    Views
    342

    Our lathes are close in year. Not all had wipers...

    Our lathes are close in year. Not all had wipers back then, including engine lathe tail stocks.

    The turret tail stock on my 2H did not either. It was on my mind during the build because I can't...
  18. Replies
    24
    Views
    799

    For the wife, I find casual comments help: "Did...

    For the wife, I find casual comments help: "Did you lose weight ?" , "are those new clothes, sure looks pretty" :D

    On the wear, on short length cuts, let's say 2" or 3". You will probably hold...
  19. It turned out unnecessary, but I used a black...

    It turned out unnecessary, but I used a black marker to mark the ways and the levels. When splitting hairs I did'nt want to keep getting fouled up. As it turned out, I cleaned and de-burred...
  20. Replies
    5
    Views
    241

    Bronze is better, particularly c932. It has a...

    Bronze is better, particularly c932. It has a little lead in the mixture. The lead has anti friction properties which make it preferred in bearing material. Nearly all the shafts in apron turn very...
  21. Looking to finish trimming this out. When using...

    Looking to finish trimming this out. When using test bars I may want to lift head stock and shim, so I don't want to block the left side head stock clamp by installing the gears on left end.
    ...
  22. Getting close to starting back on this. Picked up...

    Getting close to starting back on this. Picked up some oil I plan to use for this, and I think will become my "default" oil of choice for most related items. Going with DTE Heavy, which is equivilent...
  23. Replies
    11
    Views
    342

    I'd say not just contact, but a touch of pressure...

    I'd say not just contact, but a touch of pressure also. You don't want fine grit slipping past lightly touching felts.

    Also don't worry if you feel you drilled wrong. If the pre-cut felt feels...
  24. Replies
    9
    Views
    436

    No doubt, but consider the mindset back then. As...

    No doubt, but consider the mindset back then. As big as it is, bet you its rated for 3/4hp to 1hp. :D
  25. Replies
    5
    Views
    241

    Grizzly will sell serial card info, but not...

    Grizzly will sell serial card info, but not dimension prints. Not sure if they have them or not, they just listed they won't sell them.

    Your best bet is finding someone's particular repair of a...
Results 1 to 25 of 1358
Page 1 of 55 1 2 3 4