Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: cyanidekid

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    258

    I ordered my Bison pinion through Small Tools in...

    I ordered my Bison pinion through Small Tools in Ohio, they are helpful and would know where to get that, so give them a call.
  2. Replies
    29
    Views
    5,877

    well, really depends on the local market, and the...

    well, really depends on the local market, and the "nature" of the auctioneers in your area. in some places, the auction companies are the last ones you would involve. (the ones who collude with their...
  3. don't think a "material" is quite right.. hung up...

    don't think a "material" is quite right.. hung up the apron..yea, an image is better. I know it doesn't work like that, but if a moderators input is required anyway..
  4. Replies
    19
    Views
    1,540

    the OP's items look more like internal pipe...

    the OP's items look more like internal pipe gripping tools..271592
  5. Replies
    19
    Views
    1,540

    then don't look at these! 271591

    then don't look at these! 271591
  6. Replies
    19
    Views
    1,540

    no, THESE are hip replacement tools! 271583

    no, THESE are hip replacement tools! 271583
  7. as to the "loose" tip, I doubt it is supposed to...

    as to the "loose" tip, I doubt it is supposed to be loose. logic goes like this; if it comes with a wire standoff option, its not a drag type intended for contact, so why would it rely on depressing...
  8. oh, and none of us has EVER seen a metal can that...

    oh, and none of us has EVER seen a metal can that leaked... and even if they did seal up perfectly every time, it's a plasma CUTTER. look, I'm not sayin' this is the worst thing ever, just not a...
  9. to those who may watch the above, PLEASE remove...

    to those who may watch the above, PLEASE remove flammables such as Minwax oil stain or MEK from the work area before plasma cutting torch cutting or welding!!!
  10. Replies
    29
    Views
    1,718

    As you have discovered, these speeds just won’t...

    As you have discovered, these speeds just won’t work for cutting steel. Light cuts in Aluminum can generally be accomplished with woodworking tools at near woodworking speeds, and in modern...
  11. don't sell it, just figure out how not to trash...

    don't sell it, just figure out how not to trash it - spacer wire thing, and pre-drill if starting away from the edge. piercing is hard on tips!. run whatca got!

    Unless your ramping up to do a lot...
  12. Replies
    6
    Views
    472

    Blindly assuming can be very similar to blindly...

    Blindly assuming can be very similar to blindly following. Are you assuming they should be asking for your suggestions? Just a question;)
  13. Replies
    15
    Views
    1,487

    5 min isn’t long enough to tell anything,...

    5 min isn’t long enough to tell anything, otherwise, some good leads above...
  14. Replies
    6
    Views
    472

    Yea, there are lots of ways to do it, (laser...

    Yea, there are lots of ways to do it, (laser comes to mind) but they said “I’ve been assigned the task of building a die”...soo many don’t READ the post!!
  15. Replies
    23
    Views
    1,344

    well, that is a whole different subject! (how to...

    well, that is a whole different subject! (how to set the spindle up for regrinding the taper)maybe its been covered?

    back to the topic, perhaps for both availability and travel length, you...
  16. Replies
    20
    Views
    1,637

    Also, ask your electric company if they have an...

    Also, ask your electric company if they have an incentive program, some utilities will actually rebate 100% of the purchase cost of an inverter unit if it’s replacing an old transformer C/C unit.
  17. Replies
    20
    Views
    1,637

    The old transformer constant current units...

    The old transformer constant current units basically reduced the output current at the lower amperage settings by wasting a good part of the unneeded excess amperage as heat.

    If you are in an...
  18. Replies
    6
    Views
    692

    Well, the obvious factor here is quantity. If you...

    Well, the obvious factor here is quantity. If you ask a manufacturer (especially S&W) they will probably be ordering in mill run quantities, tons of each size. Doubt the mill would sell you, say, 10...
  19. ok copy,faceplates. thanks, I'm looking for back...

    ok copy,faceplates. thanks, I'm looking for back plates.
  20. can I get more on the D1-6 faceplates? just to...

    can I get more on the D1-6 faceplates? just to confirm, they are blank chuck back plates, yes? new or used? any info an brand or material? (cast iron, or steel?) all pins intact and in good...
  21. Replies
    31
    Views
    2,711

    my technique for surface rust on ways is a single...

    my technique for surface rust on ways is a single edge razor blade, a hard Arkansas stone (or a piece of 1000 grit wet or dry) to polish and dress the blade. soften it up with light oil, dress blade...
  22. Replies
    8
    Views
    720

    why do you need a 1" wide wheel? If it is set up...

    why do you need a 1" wide wheel? If it is set up for a 1/2" wheel, there is probably a reason, such as the HP of the motor. doubling the contact area may not be a good idea on a small grinder like...
  23. Replies
    31
    Views
    2,711

    Ok, this is the best story of finding old iron...

    Ok, this is the best story of finding old iron I've ever herd.. "chasing a suspect through the desert and saw..." !!
  24. not sure, ill have a good look and check it for...

    not sure, ill have a good look and check it for wear. It would however be best for you to get the right one for your lathe even though its not likely you will be threading full length that often, so...
  25. I have a leadscrew for a 16 in good shape, it’s ...

    I have a leadscrew for a 16 in good shape, it’s 77 1/2 overall, and the right side mounting bracket for it. Also a rack (52”) so guess they are off a 6’?
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4