Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Seaman

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    462

    Did that several years ago, but the model I had...

    Did that several years ago, but the model I had you had to replace the drum also. The detergent rots away the pot metal spider. When mine went out it took the bearing also. Didn't know it for a...
  2. Replies
    32
    Views
    1,973

    could you make a siphon pipe out of 2 or even 3...

    could you make a siphon pipe out of 2 or even 3 inch pvc and connect the two tanks? Put a fill port in the crossover between the two drops into the tanks. Quick and inexpensive and would proof the...
  3. one on fleabay right now. NOS Safe brass jaws...

    one on fleabay right now.

    NOS Safe brass jaws Jacobs 100CR 7814 No. 02525 for 100CR Armature chuck kit | eBay
  4. Replies
    21
    Views
    1,992

    Precision Urethane, Hempstead TX

    Precision Urethane, Hempstead TX
  5. Replies
    14
    Views
    549

    LB25 has the wye-delta contactor to change the...

    LB25 has the wye-delta contactor to change the speed range. I had the exact issue you're having with an LB25 and replaced the two contactors.

    Same as yours, would only run in either high or low...
  6. Replies
    14
    Views
    741

    I didn't run through all your dimensions, but the...

    I didn't run through all your dimensions, but the male key in the old set is held in with a socket cap screw. If you removed this key, are the old jaws equivalent to an American Standard jaw? If...
  7. Thread: Belt Grinders

    by Seaman
    Replies
    43
    Views
    3,402

    I've got a Baleigh 6x something that is a POS. ...

    I've got a Baleigh 6x something that is a POS. Don't go there.

    Yes it's Chicom and it shows.
  8. Replies
    14
    Views
    1,404

    the coil is 220V, so you need two legs to the A1...

    the coil is 220V, so you need two legs to the A1 and A2 terminals. The small red wire from L2 runs down the side to one of these terminals. The second should be the white wire on L1, going to the...
  9. I've got the Sidney drive on mine. Get the...

    I've got the Sidney drive on mine. Get the electrical schematics first. There are three, maybe four, transformers to reconfigure for the lower voltage. Plus, rewiring the coolant pump. You might...
  10. Replies
    34
    Views
    3,208

    Been using Dyneema rope on offshore winches for...

    Been using Dyneema rope on offshore winches for 20 plus years. 500 tonne winches, 6" diameter rope. Standard drum winches, traction winches, best stuff since canned beer and sliced bread. Ever...
  11. I used the M700 for a spindle motor control, via...

    I used the M700 for a spindle motor control, via HMI screen, and used the single output switch to control the coolant pump. You can configure the switch to look at one certain parameter within the...
  12. I had a similar issue. Needed a standard double...

    I had a similar issue. Needed a standard double row deep groove ball with seals and the snap ring. Unobatinium off the shelf.

    Try Quality Bearings Online, UK company. They have their online...
  13. sorry to hear about all this misfortune. I'm...

    sorry to hear about all this misfortune. I'm sure you'll get things sorted with time.

    Willis has always been helpful to me also.

    BTW, I have 50292. Also 9/69. So, our machines were on the...
  14. Replies
    10
    Views
    1,497

    looks like it is bolted from the rear with bolts...

    looks like it is bolted from the rear with bolts 42 or 25. Need to remove the entire shaft via spanner nut removal. It looks like.

    Good luck

    Dave
  15. Replies
    13
    Views
    1,872

    short update on the project: Two 2hp Black Max...

    short update on the project:

    Two 2hp Black Max motors with encoders will be here next week.
    Two Control Techniques M700 drives will be here next week also.

    I stepped down the HP from the...
  16. Replies
    13
    Views
    1,872

    Many thanks to so many, just didn't know. I'll...

    Many thanks to so many, just didn't know. I'll digest it a bit and ask more when required.

    FWIW, existing spindle motors are 30+ years old and shouldn't be used. The original U frame oil pump...
  17. Replies
    13
    Views
    1,872

    Encoder requirements for new VFD system

    Rebuilding P&W twin spindle gun drill and the next step is to replace the ancient spindle drive motors and the change pulley setup with dual VFD's.

    Since these are basically spindle drives, I'd...
  18. Replies
    14
    Views
    2,575

    You need to find a schematic, I think there are...

    You need to find a schematic, I think there are several wires missing/wrong location. Or you have a dinosaur there.

    The CNC start button should be connected to 120vac and the small grey terminal...
  19. Replies
    17
    Views
    2,461

    slot the sheet metal cover and leave the tapped...

    slot the sheet metal cover and leave the tapped hole as is.
  20. Replies
    1
    Views
    1,179

    Oil pressure on P&W deep hole drill

    Looking at the cutting oil system on a vintage P&W 1/2B drill and was hoping someone could chime in on what is the working pressure of that system. My machine is basically original, with the...
  21. Update: Yesterday spent some time getting the...

    Update: Yesterday spent some time getting the incoming AC voltage a bit more balanced from the transformer. Machine voltages agree with the trouble shooting chart in manual. No change. Replaced...
  22. Thanks Bob for the reply. Yes fancy new PS...

    Thanks Bob for the reply.

    Yes fancy new PS from ITS.

    Looks like it's going to be some hunting and pecking to see whats acting up. Yes it is in an unconditioned shop, but none of the other...
  23. FADAL resetting/restarting when going to auto mode

    I've owned FADAL's for more than a decade and haven't experienced this yet, hope someone can help me out.

    Issue: Perform normal cold start, go to part home position and the machine doesn't move...
  24. Replies
    4
    Views
    1,164

    A brief update. All the hydraulics checked...

    A brief update.

    All the hydraulics checked out, which is what I thought since it was thumping. Removed the entire rear hydraulics panel to expose the jog clutch itself. Removed it, looked fine. ...
  25. Replies
    2
    Views
    1,884

    I've had mine apart down to the clutch itself. I...

    I've had mine apart down to the clutch itself. I just needed to repair the aluminum clutch housing as some gorilla tried to pry off the pulley/brake without taking it apart. Leaked a bit of oil...
Results 1 to 25 of 90
Page 1 of 4 1 2 3 4