Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: NewToEDM

Page 1 of 2 1 2

Search: Search took 0.00 seconds; generated 50 minute(s) ago.

  1. Replies
    7
    Views
    1,062

    Thank you Marcus , but i never worked a job like...

    Thank you Marcus , but i never worked a job like that. I will figure it out.

    I am pretty sure that was obvious that i am not an english native speaker before you pointed this mistake, if you have...
  2. Replies
    7
    Views
    1,062

    If i would do a job on 3 axes and use the same X...

    If i would do a job on 3 axes and use the same X and Y and on C axis i start with 0 degrees at start Z and end with 360 degrees on end Z it would work ? Theoretical seems achievable.
  3. Replies
    7
    Views
    1,062

    Hi Its a CNC machine , Exeron 312 from 2005. I...

    Hi
    Its a CNC machine , Exeron 312 from 2005.
    I have a round electrode cylindrical shape with diameter of 40 , i have worked with it at 0 and at 180 degrees but i have some insertion in the part...
  4. Replies
    7
    Views
    1,062

    how to erodate helix ?

    I have an old sinking edm machine and i have to erodate with a cylinder shaped electrode in a helix pattern , is it possible ?
  5. I had this problem due to oxidation of contact ,...

    I had this problem due to oxidation of contact , i took out and cleaned contact and contact support with sandpaper and it recognized the wire after that.
  6. Replies
    7
    Views
    1,308

    Thank you for your answer,if things go well i...

    Thank you for your answer,if things go well i hope i will get a good magnet this year.
    About chemical residue,i use anticorrosive spray on parts before i wirecut them.How bad could this harm my DI...
  7. Replies
    7
    Views
    1,308

    i was thinking about some small magnetic chuck...

    i was thinking about some small magnetic chuck usefull for work some small part (die) that would be hard to fix in a vice and to fix them perpendicular to table
  8. Replies
    7
    Views
    1,308

    magnet for small parts

    I always have problems fixing the small pieces to cut them to the wire .
    What small magnets would be recommended ?
  9. Replies
    7
    Views
    1,295

    It does help , and i have noticed that but sadly...

    It does help , and i have noticed that but sadly when i had red error and machine stopped i didn't looked at the filters to be sure thats the problem.
    I trusted machine's "brain"
    Tkx
  10. Replies
    7
    Views
    1,295

    I have changed the filters,machine crashed...

    I have changed the filters,machine crashed because filters wer obturated/max. pressure.
    Yes ideed,an electrovalve was the not working properly and i've changed it with one with a bigger opening.
    I...
  11. Replies
    7
    Views
    1,295

    I use tap water to complete the evaporated water.

    I use tap water to complete the evaporated water.
  12. Replies
    7
    Views
    1,295

    Filter pressure on AgieCharmilles CUT E 350

    I have changed filters 6 months ago and since than i barely worked and now i have 2.5 preassure from 2.8 max .
    What could be the reason to this ? I only cut steel .
  13. Replies
    3
    Views
    699

    Tank water level calibrated .

    Tank water level calibrated .
  14. Replies
    3
    Views
    699

    Runned calibration and got this error: Z axis...

    Runned calibration and got this error: Z axis position check related to bath level and Z min value not possible.

    I have checked the error code : It's not possible to perform the Z axis position...
  15. Replies
    3
    Views
    699

    Water level on AgieCharmilles CUT E 350

    I wanted to run a job yesterday and apparently water lvl in tank isn't updating with head lvl , when i try to run a measure the water lvl gets too high and the Z sensor stops the machine .
    Any...
  16. Replies
    2
    Views
    784

    Thanks :) Will have to order that part anyway ,...

    Thanks :)
    Will have to order that part anyway , and i have no code for it :(
  17. Replies
    2
    Views
    784

    Microfilter pneumatic plate

    Hi , i am working on a AgieCharmilles CUT E 350 and i need to replace some consumables .Can't find any info in user manual for the microfilter pneumatic plate.
  18. Replies
    7
    Views
    1,246

    Thanks for your reply Found that after i looked...

    Thanks for your reply
    Found that after i looked at some scheme for the machine , it was 1.64 (max 2.8)
    I wrote steps i followed just in case it will be helpful for someone as noob as i am.
    Good day
  19. Replies
    7
    Views
    1,246

    Pump was dry , filled with water and started....

    Pump was dry , filled with water and started.
    And few touches here and there
    Machine works , hopefully will do the job overnight
  20. Replies
    7
    Views
    1,246

    cooling system doesn't work , any switch i don't...

    cooling system doesn't work , any switch i don't know about ?
  21. Replies
    7
    Views
    1,246

    Pressure was 1.6 Filters changed Waiting to get...

    Pressure was 1.6
    Filters changed
    Waiting to get back to normal
  22. Replies
    7
    Views
    1,246

    filter pressure

    Help
    Where i can check filter pressure on Cut E 350 ?

    Default time for them to be changed at 1000 hours , i have 440 now
    Got an error - filters obstructed , chiller error - fluid shortage ...
  23. Thread: 4 axis cut

    by NewToEDM
    Replies
    2
    Views
    723

    I am waiting for a reply from them Error is...

    I am waiting for a reply from them
    Error is "Axis acceleration exceeds maximum limit"
    It stops while working , no error when i load the program
    The part i work on is 15 x 5 x 40 mm , one side has...
  24. Replies
    4
    Views
    1,165

    Any ideea what would work on CMM Mitutoyo Crysta...

    Any ideea what would work on CMM Mitutoyo Crysta Plus 544 ?
  25. Thread: 4 axis cut

    by NewToEDM
    Replies
    2
    Views
    723

    4 axis cut

    Hi
    I run a Cut E-350 , i am programming with Visi
    Made a 4 axis program and i couldn't run it on the machine
    I started the machine and i had 2 error codes - CNB 50120 and EXM 0108 and 1 warning...
Results 1 to 25 of 36
Page 1 of 2 1 2