Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jz79

Page 1 of 26 1 2 3 4

Search: Search took 0.01 seconds.

  1. a bit off topic, but this year 6082 we see here...

    a bit off topic, but this year 6082 we see here has been all over the place, some parts anodize with noticeable yellow hue, some clear gray, some have extrusion "bar end" defects, some have...
  2. Replies
    7
    Views
    277

    if it is anything like older controls (155 or...

    if it is anything like older controls (155 or 355), in conversational mode mirror function is under canned cycles

    edit: by conversational mode I mean Heidenhain programming language
  3. Replies
    29
    Views
    1,140

    it should be 69.85mm for 50 taper, or 2.75",...

    it should be 69.85mm for 50 taper, or 2.75", diameter at the gauge line that is
  4. Replies
    29
    Views
    1,140

    there was a video from Big Kaiser about checking...

    there was a video from Big Kaiser about checking the fit of their big plus spindles, and they used a bead (3 or 4 beads actually) of the blue axially on the taper, not wipe on, but a narrow bead, and...
  5. Replies
    42
    Views
    1,703

    brinelling isn't the main issue when everything...

    brinelling isn't the main issue when everything is on size etc. - hole size and depth and operator error loading different length pin or something of that sort

    everything can be worked out, you...
  6. Replies
    42
    Views
    1,703

    sounds a lot like one of those - when you have a...

    sounds a lot like one of those - when you have a hammer, everything looks like nail...
  7. Replies
    23
    Views
    1,197

    perhaps no one is willing to write a very long...

    perhaps no one is willing to write a very long essay discussing all measurement scenarios, since it would be quite a waste of time...
  8. buy some 2part urethane or silicone rubber and...

    buy some 2part urethane or silicone rubber and make cylinder plugs that are just barely larger than the minor diameter of the thread, so it is easy to push in and pull out with tweezers? making a...
  9. Thread: Painting my FP2

    by jz79
    Replies
    29
    Views
    1,731

    there seems to be a compression setting also for...

    there seems to be a compression setting also for it, in case the 1024px file is still large because of inherited quality setting, try this:
    sips -Z 1024 IMG.jpg -s formatOptions 70

    70 is a...
  10. Thread: Painting my FP2

    by jz79
    Replies
    29
    Views
    1,731

    image file size varies depending on how well the...

    image file size varies depending on how well the compression algorithm handled it, PM forum software seems to automatically resize images above around 1200px in either direction and reduce them to...
  11. you can tap the ER nut that is lightly tightened...

    you can tap the ER nut that is lightly tightened into practically zero TIR measured on the tool, it helps it seat more evenly, then tighten it down further, with some luck the runout will be minimal...
  12. Replies
    57
    Views
    1,810

    before you grind anything, take it all apart,...

    before you grind anything, take it all apart, clean and inspect, pay close attention to the scroll and the threads on the jaws, chips and debris stuck there can cause runout
  13. I suspect it is one of those small round tub...

    I suspect it is one of those small round tub tumblers, right?

    why not rig up a portable AC unit to blow cold air from the top inside the bowl, and it would work even better if you would make...
  14. Replies
    5
    Views
    533

    OP isn't looking for a way of getting the coolant...

    OP isn't looking for a way of getting the coolant through the pull stud, but "from the side" into the tool holder or directly into the tool

    probably won't happen, but I'm curious why would one...
  15. Replies
    21
    Views
    1,490

    it is probably Windows auto correct as Ross says,...

    it is probably Windows auto correct as Ross says, here is image of the setting location I googled up, it may be slightly different in German Windows, but should be under the same section in Settings,...
  16. Replies
    35
    Views
    1,540

    you're confusing the 35$ line with the 3.5$...

    you're confusing the 35$ line with the 3.5$ products :D

    as EG said, the not so cheap ones start to look usable out of the box

    the 3.5$ ones are the gritty ones with sharp corners and shoddy...
  17. Replies
    1,008
    Views
    130,577

    there was some odd stuff going on with internet...

    there was some odd stuff going on with internet comms with China at the beginning of the year, maybe g-coder05 can comment on that

    my situation: for last 5-6 years I was buying supplies for...
  18. I bought a Kuka robot a while back from Germany,...

    I bought a Kuka robot a while back from Germany, the cables were cut not far from the control cabinet, which is fine, they may have ran into some difficult to access channel or other conduit, but the...
  19. Replies
    1,008
    Views
    130,577

    it's not so much as a joke as a smoke screen, to...

    it's not so much as a joke as a smoke screen, to give the masses something to fight about, rather than beat the government to pulp for failing so bad on the pandemic front

    good old divide and...
  20. Replies
    3
    Views
    422

    one thing to note - soft water =/= softened...

    one thing to note - soft water =/= softened water, and what matters in this context is the amount of dissolved minerals, water may be described as "soft" while still having high mineral content which...
  21. Replies
    20
    Views
    1,385

    no affiliation or experience with these, I...

    no affiliation or experience with these, I remembered an old video where some Russian made a tool like this, chain driven, but it was probably for a larger diameter work piece, he used it to mill...
  22. Replies
    18
    Views
    917

    people regard us, Eastern Europeans, as coarse...

    people regard us, Eastern Europeans, as coarse and difficult to deal with because we'll say what we really think (most of the time anyway)

    and this thread would benefit a lot from that, else it is...
  23. Replies
    31
    Views
    1,416

    It looks like that in that Mode5 the control is...

    It looks like that in that Mode5 the control is telling the X axis to move for some reason, that is what that 1.25V is on those leads, and if I understand what you did previously, then the Bosch...
  24. Replies
    17
    Views
    1,685

    the right version of the MH400 This Old Tony...

    the right version of the MH400 This Old Tony should have started with, but then again, less content for the YT audience... :D
  25. Replies
    6
    Views
    522

    draw on paper how the ID cut looks like axially...

    draw on paper how the ID cut looks like axially and it will be immediately apparent why it is important for the tool to be above the center line and not below and why it is exactly the opposite for...
Results 1 to 25 of 643
Page 1 of 26 1 2 3 4