Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: millwrong

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Wanted ! ! !

    by millwrong
    Replies
    446
    Views
    143,984

    Sticky: Looking for W20 collet blocks. Really need an...

    Looking for W20 collet blocks. Really need an hexagonal block. also,looking for emergency collets in W20. Anyone have extras they want to unload?
  2. You need a jumper wire from line to #5. The...

    You need a jumper wire from line to #5. The drawing shows a SPDT output controlled by the power side.
  3. Replies
    328
    Views
    12,087

    "EPA, my all time favorite graffito was written...

    "EPA, my all time favorite graffito was written above an elevator door in the parking garage at the baseball park. Due to the limitations of this keyboard, I cannot exactly reproduce it here, so...
  4. Replies
    40
    Views
    2,212

    "You deal with air dentistry changes from...

    "You deal with air dentistry changes from daylight to nighttime" The award for the best miss-typing goes to; CarbideBob!! Thanks for the laughs on this one! :D I know what you were looking for, but I...
  5. Replies
    40
    Views
    2,212

    "The Sports Car Engine" by Colin Campbell "The...

    "The Sports Car Engine" by Colin Campbell
    "The High-Speed Internal-Combustion Engine by
    Harry Ricardo"
    "Tune to Win: The art and science of race car development and tuning"

    Thanks to all! As I...
  6. Replies
    40
    Views
    2,212

    "ahhh Winnipeg . . . I have family spread around...

    "ahhh Winnipeg . . . I have family spread around that neck of the woods."

    Not quite the "neck". A little lower down the spine,me thinks.:D
  7. Replies
    40
    Views
    2,212

    351 stroker-but why engine dependent? I'm not an...

    351 stroker-but why engine dependent? I'm not an engine guy by any stretch of the imagination. The basics of fuel/timing,etc. are some of the variables that people "tune" for? Isn't the objective to...
  8. Replies
    40
    Views
    2,212

    OT: performance engine tuning references

    I've got a friend who likes throwing all his cash at a 1/4 mile car. He's at the point that tuning is essential for consistency. What are the "bibles" of performance engine tuning? Any good...
  9. incoming PM.

    incoming PM.
  10. Replies
    8
    Views
    1,250

    Thanks all for the help! mTeryk, it scorches me...

    Thanks all for the help! mTeryk, it scorches me that I missed that post! Oh well, it's Friday; so I will buy you all virtual drinks,and whatnot in appreciation!:cheers:
  11. Replies
    8
    Views
    1,250

    I did. Went through six-odd pages. I'll be the...

    I did. Went through six-odd pages. I'll be the first to admit that my google-foo is weak.
  12. Replies
    8
    Views
    1,250

    45/5 buttress thread insert availability

    I've been trying to order some W20 arbor blanks from Schaublin. I've got the cash burning a hole in my pocket, but it seems no one who represents Schaublin wants to take my cash.I haven't exhausted...
  13. PM inbound. Vice Part – 9625954 - $750.00 •...

    PM inbound.

    Vice Part – 9625954 - $750.00
    • Vise jaw size: 4”
    • Max Opening: 5.512”
    • Weight: 66 lbs
    • Dimensions: 16.5 × 4 × 5 in
  14. PM sent to your gmail account. I think.:confused:

    PM sent to your gmail account. I think.:confused:
  15. Replies
    70
    Views
    5,821

    Tried to PM you. Computer told me to go away;said...

    Tried to PM you. Computer told me to go away;said your inbox is full.
  16. Replies
    70
    Views
    5,821

    Interested in the cross drill jig. I'm not sure...

    Interested in the cross drill jig. I'm not sure if it'll fit in a flat rate? Whatca' think?
  17. Replies
    11
    Views
    1,742

    I believe that Harvey Tool has spotting drills...

    I believe that Harvey Tool has spotting drills down to 0.020". Also various geometries as well. Happy spending!
  18. Replies
    47
    Views
    14,967

    I stand corrected!:dopeslap: My only excuse is...

    I stand corrected!:dopeslap: My only excuse is old age; " I'm surprised that old-timers confuse him with a used machinery dealer":codger:
  19. Replies
    47
    Views
    14,967

    "Lenmark has the pictures and prices for you to...

    "Lenmark has the pictures and prices for you to look at.":skep:
    For the uninformed Lenmark is an industrial surplus reseller; unlikely this refers to any private sales.
  20. Replies
    1
    Views
    506

    led work/flood lights

    Having gone through the various North American power tool manufacturers offerings; the "cob" style with batteries,and rechargeable, complete with hooks, magnets,tri-pods,500 lumen to 5000 lumen rated...
  21. Replies
    10
    Views
    2,298

    The few times I've used packed bits for boring...

    The few times I've used packed bits for boring deep holes the wood bearings had to be turned to size separately. What goes unremarked is how he sizes the wood support bearing for his boring bar. It's...
  22. Replies
    36
    Views
    4,006

    YouTube (https://youtu.be/Sh8mNjeuyV4) "I'm...

    YouTube

    "I'm not dead!!"
  23. The place to start will be the check valve. That...

    The place to start will be the check valve. That will be between the line going into the tank, and the tank itself. Usually located just outside the tank. There are multiple styles of checks, so a...
  24. Replies
    4
    Views
    1,441

    Blocks have arrived in fine shape! I only need a...

    Blocks have arrived in fine shape! I only need a jillion more to build a shiny new house!
  25. Replies
    4
    Views
    1,441

    I'll take em. PM coming.

    I'll take em. PM coming.
Results 1 to 25 of 176
Page 1 of 8 1 2 3 4