Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Illinoyance

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    21
    Views
    1,114

    Remove the collet from the spindle. Remove screw...

    Remove the collet from the spindle.
    Remove screw no. 31
    Rotate the lever so one of its ears aligns with the link 32.
    Use the lever to pry against the link to pull the assembly off the spindle.
    ...
  2. Lift off the table and remove the balls and...

    Lift off the table and remove the balls and separators. Keep these separate during the move. On mine the outlet of the lube pump was almost flush with the bottom of the base. It can be damaged if...
  3. Replies
    5
    Views
    669

    NW is a diamond core drill manufacturers...

    NW is a diamond core drill manufacturers association standard. You can probably buy a copy of the standard from DCDMA. As I remember it is a regular square thread. You might buy an NW coupling and...
  4. Replies
    26
    Views
    2,128

    If the soil used as backfill was properly...

    If the soil used as backfill was properly compacted its strength an density will exceed that of the virgin soil so it may be possible to pour the machine foundation directly on the backfill. Have a...
  5. Cylinder repair components. See if they have...

    Cylinder repair components.
    See if they have drop that will fit your needs.
  6. PM me with your e-mail address and will send you...

    PM me with your e-mail address and will send you a copy.
  7. Replies
    4
    Views
    622

    Photos! Dimensions of the threads at the...

    Photos!
    Dimensions of the threads at the compressor outlet and whether tapered or straight. Parker probably has fittings that can be adapted.
  8. Have you looked at 80/20 extrusions for the track?

    Have you looked at 80/20 extrusions for the track?
  9. Replies
    26
    Views
    1,937

    An alligator shear would have been a lot faster. ...

    An alligator shear would have been a lot faster. Flattened ends would have made the cut pieces useless.
  10. Thread: Dapra

    by Illinoyance
    Replies
    2
    Views
    421

    Search under Arnold vise. Fresmak / Arnold high...

    Search under Arnold vise.
    Fresmak / Arnold high pressure hydraulic vises

    BTW I have an arnold 6" x maybe 12" opening I want to dispose of. It is air over hydraulic. The hydraulics need rebuilt....
  11. Replies
    1
    Views
    391

    Freaking DuPont overhaul.

    Freaking DuPont overhaul.
  12. Replies
    10
    Views
    818

    It could be a shrink rule for pattern makers. ...

    It could be a shrink rule for pattern makers. The marking is unusual. They were usually marked in inches per foot. The amount of shrink is large, possibly double shrink for making cast metal...
  13. I didn't think they made taper pins that large.

    I didn't think they made taper pins that large.
  14. A simple rule for setting the compound angle is...

    A simple rule for setting the compound angle is this: the compound feed should be parallel with the trailing flank of the tool.

    There are some who prefer to plunge feed. The rule doesn't apply to...
  15. There are a couple of issues on the NS series...

    There are a couple of issues on the NS series Grob saws.
    When changing the belt from high to low range or vice versa it almost requires 3 hands to do the belt change.
    The air pump for the chip...
  16. Re: carbide flat stock Grob sells carbide guide...

    Re: carbide flat stock
    Grob sells carbide guide blocks that last forever (almost).
  17. Replies
    12
    Views
    963

    In my youth I spent many hours threading 2" pipe...

    In my youth I spent many hours threading 2" pipe with a Toledo threader.
  18. Replies
    23
    Views
    1,567

    Spend $30 on an angle gauge set. 18 Piece 5 to...

    Spend $30 on an angle gauge set.
    18 Piece 5 to 90 Degree Primary Angle Gage Set
  19. Riverview Surplus in Moline IL has several...

    Riverview Surplus in Moline IL has several workheads I believe were from a Cinc. No 2. I haven't asked the owner what he wants for them but I expect it will be a fraction of the flea bay price.
  20. Replies
    7
    Views
    851

    Find a friend who has a lathe and ask him to make...

    Find a friend who has a lathe and ask him to make a new nut for you. A gift of certain liquids might smooth the way.
  21. You should have done that BEFORE posting.

    You should have done that BEFORE posting.
  22. Replies
    5
    Views
    621

    I have a 10K. The motor is 3 phase 1200 rpm.

    I have a 10K. The motor is 3 phase 1200 rpm.
  23. I have Tenthset heads in 3/8 and 1/2" sizes. I...

    I have Tenthset heads in 3/8 and 1/2" sizes. I am quite satisfied with them. They are my favorite boring heads. Beware of any Tenthset that was used with coolant. Both my Tenthsets were bound up...
  24. Many years ago I owned a tapper made by Ettco. ...

    Many years ago I owned a tapper made by Ettco. It resembled a corded 3/8" pistol grip electric drill. Ir ran forward when pushed and reverse when pulled.
    The idea of an electric tapper is...
  25. I am no a fan of extruded threads on the clip. ...

    I am no a fan of extruded threads on the clip. Why not eliminate all the fuss and use a standard nut and flat washer?
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4