Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: deltap

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. I built one as you describe for a framed stucco...

    I built one as you describe for a framed stucco chimney I had in FL. I used stainless and welded the seams. I have sheet metal experience. You could make it flat from one piece. With a welded collar...
  2. Replies
    15
    Views
    1,008

    What type of heat exchanger? Low cost might be...

    What type of heat exchanger? Low cost might be brazed plate 316ss. Or you could order special order monel. Some are constructed with an air gap so if it fails or leaks it will not contaminate the...
  3. Replies
    4
    Views
    513

    Home depot has one like that for retailing custom...

    Home depot has one like that for retailing custom wire lengths.
  4. Replies
    12
    Views
    1,617

    Weld a stout washer to the pin, then weld a hex...

    Weld a stout washer to the pin, then weld a hex nut to the washer. Thread a bit of all thread into the nut and use slide hammer or bushing and wrench to pull. Small impact works well. You can buy...
  5. Replies
    23
    Views
    1,952

    What they call a lever hoist is really just a...

    What they call a lever hoist is really just a come along that is meant for pulling horizontally. A chain fall will be easier to use than constantly moving a lever back and forth.
  6. Replies
    20
    Views
    1,966

    Take the motor apart on the rpc you bought and...

    Take the motor apart on the rpc you bought and replace the bearing on each end. It's an electric motor with no shaft sticking out. 4 screws or rods and the end bell pops off. You can then slide the...
  7. Replies
    17
    Views
    1,688

    A box wrench with cheater pipe slid over it would...

    A box wrench with cheater pipe slid over it would be a good alternative to a socket.
  8. Replies
    17
    Views
    1,688

    I had lots of experience with locktite at work....

    I had lots of experience with locktite at work. If you want it to bond you have to degrease the threads, dry, and then apply the locktite. Forget the grease until locktite has cured. We would apply...
  9. Many of those springs are sold by expected number...

    Many of those springs are sold by expected number of cycles to failure with 10,000 being about the lowest. Larger diam wire and longer spring should give more cycles. You should weigh the door and...
  10. Replies
    17
    Views
    1,301

    Is it hollow? 3 jaw chuck internal grip mounted...

    Is it hollow? 3 jaw chuck internal grip mounted on rotary table. Bolt to mill table so chuck is horizontal.
  11. Replies
    18
    Views
    13,274

    Square D makes a generic pressure switch with...

    Square D makes a generic pressure switch with unloader built in. All it does is bleed air between check valve and compressor. Make sure check valve works. It's a ower cost option. Dental specs may be...
  12. Replies
    8
    Views
    872

    Looks about same material as excavator...

    Looks about same material as excavator pins/bushings.
  13. Replies
    29
    Views
    1,577

    Do you need to reverse the motor? If not a single...

    Do you need to reverse the motor? If not a single pole switch with only 2 screw terminals will work. Green to ground on motor case. White to yellow on motor. Black to switch and black from other side...
  14. Replies
    29
    Views
    1,577

    Do you need to

    Do you need to
  15. Replies
    6
    Views
    707

    2 wires it ain't 3 phase. A single phase motor...

    2 wires it ain't 3 phase. A single phase motor with a bad end switch or start cap will do that. How do you change feed rate with ac one speed motor?
  16. Start threading with diam. a bit smaller so there...

    Start threading with diam. a bit smaller so there is a flat on thread crest. Chamfer end 45 degrees. Finish thread start with file.
  17. Replies
    14
    Views
    960

    Can be caused by all of the above. Check tension....

    Can be caused by all of the above. Check tension. Set blade guides + .001" wider than blade. Check downfeed pressure. Check blade for wear on one side.
  18. Replies
    7
    Views
    553

    To be able to switch from wye to delta you need 6...

    To be able to switch from wye to delta you need 6 leads coming out of the motor. Motor looks like single voltage.
  19. Replies
    29
    Views
    2,253

    What others have said. Add 1 pitch to minor dia....

    What others have said. Add 1 pitch to minor dia. , so 2.186. Cut a 2-3/16 -10 and see if it fits.
  20. Replies
    27
    Views
    2,274

    On some I have seen the tapered center part...

    On some I have seen the tapered center part extends through to the back side of the pulley. If so you can put a sleeve against the center part and use a puller or tap bolts to force the pieces apart....
  21. Replies
    18
    Views
    908

    There many online calculators where you input...

    There many online calculators where you input speeds and pulley diameters to get what you want. Speed x diameter of driver pulley equals speed x diameter of driven pulley.
  22. Replies
    28
    Views
    17,568

    HH-66 vinyl cement. Works good on tarps. You will...

    HH-66 vinyl cement. Works good on tarps. You will need patching material for lap seams.
  23. Download Parker o - ring handbook. Pdf

    Download Parker o - ring handbook. Pdf
  24. Replies
    4
    Views
    295

    You may be able to cross reference it with an...

    You may be able to cross reference it with an asco valve.
  25. Replies
    59
    Views
    3,877

    If a standard size. 1. Impact socket 2. Box...

    If a standard size. 1. Impact socket 2. Box wrench 3. Flare nut wrench. If the space is too tight for a hex wrench switch to a socket head cap screw. At 220 torque must be 3/4 or larger screw.
Results 1 to 25 of 290
Page 1 of 12 1 2 3 4