Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: rustytool

Page 1 of 47 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    58
    Views
    4,072

    Here's a link the the Anglo-Swiss...

    Here's a link the the Anglo-Swiss website.http://anglo-swiss-tools.co.uk/tripan-tool-posts/
  2. Replies
    58
    Views
    4,072

    What make of lathe is that ? I'd like to see the...

    What make of lathe is that ?
    I'd like to see the man cave that can house a lathe that size.
    I guess "downsizing" means different things to different people.
  3. Replies
    58
    Views
    4,072

    I forget exactly. It was around 5 or 6 hundred US...

    I forget exactly. It was around 5 or 6 hundred US dollars.
    I think you can buy them new through the Anglo-Swiss tools website in the UK.
  4. Replies
    58
    Views
    4,072

    I was offered one but the seller wanted way more...

    I was offered one but the seller wanted way more than I was willing to pay.
    They're not too common in the US though.
  5. I'm going to have to get down there next summer....

    I'm going to have to get down there next summer.
    That's pretty cool.
  6. Replies
    58
    Views
    4,072

    Put new bearings in the coolant pump and got it...

    Put new bearings in the coolant pump and got it back in the cleaned up sump.
    The stud for the indexing turret tool post has a flange on the bottom and is secured by pins and screws from underneath....
  7. Replies
    19
    Views
    969

    drom, How tall is the #3 ? I have a #1 and am...

    drom, How tall is the #3 ?
    I have a #1 and am looking to upgrade.
    Needs to fit through my 8' tall shop door.
    Thanks,Greg.
  8. Replies
    58
    Views
    4,072

    According to this chart from Tony's lathes.uk...

    According to this chart from Tony's lathes.uk website it was made in either 1962, 1963 or 1964.
    1964 being the last year of production.Holbrook Serial Numbers
  9. Replies
    58
    Views
    4,072

    Cleaned the headstock oil filter. The round...

    Cleaned the headstock oil filter. The round cylinder is a magnet and goes inside the tube with the steel rings. Then I dove headfirst into the coolant sump and pump.
    269925269926269927269928269929
  10. Replies
    51
    Views
    3,103

    Are you in Ohio or Idaho ?

    Are you in Ohio or Idaho ?
  11. Replies
    58
    Views
    4,072

    Got the gear box cover on. The only tricky part...

    Got the gear box cover on. The only tricky part was having the worm gear in the proper rotational orientation so that when the sliding tumbler gear is raised it is in the proper position....
  12. Replies
    19
    Views
    1,599

    I have. Everyone seems to be a little different...

    I have. Everyone seems to be a little different but basically you undo the bolts at the four corners, disconnect wiring and belts, jack it up a little from underneath with a pallet jack and it will...
  13. Replies
    3
    Views
    467

    I'm thinking it is for turning the drill bit at...

    I'm thinking it is for turning the drill bit at the same time the workpiece is turning in the lathe spindle such as is done with the Levin Micro Drilling Attachment.LevinLathe.com: MICRO-DRILLING...
  14. Replies
    19
    Views
    1,047

    I've had success with derusting large pieces with...

    I've had success with derusting large pieces with evapo rust by covering the areawith paper towels, soaking with the evapo rust then covering with plastic sheet. Occasionally lifting the sheet to...
  15. Replies
    24
    Views
    1,792

    Pretty soon even clean fresh air in California...

    Pretty soon even clean fresh air in California will cause cancer and it will be illegal to breathe.
  16. Replies
    51
    Views
    3,103

    This is one of my favorite youtube...

    This is one of my favorite youtube channels.YouTube
  17. Replies
    58
    Views
    4,072

    Got the saddle and apron on and the leadscrew,...

    Got the saddle and apron on and the leadscrew, power feed rod and start/stop/forward/reverse rods in.
    269729269730269731
  18. Replies
    58
    Views
    4,072

    Cleaned up the rack and start stop switch gears....

    Cleaned up the rack and start stop switch gears. They have timing marks punched in them which makes timing them a non issue. New felts for the way guards.
    269608269609269610269611269612
  19. Replies
    20
    Views
    3,020

    But the exchange rate today is 1 Canadian dollar...

    But the exchange rate today is 1 Canadian dollar equals .76 US dollar.
    And from my experience Lenmark does have some wiggle room in negotiating the final price.
  20. Replies
    58
    Views
    4,072

    L7, I haven't even run it yet so I can't say in...

    L7, I haven't even run it yet so I can't say in that respect but just by observing the build quality it is very heavily built and without compromise.
    Like everything some people just like them and...
  21. Replies
    58
    Views
    4,072

    Is that the gear box on the front or on the left...

    Is that the gear box on the front or on the left end ?
  22. Replies
    20
    Views
    3,020

    The youtube guys should collectively buy the...

    The youtube guys should collectively buy the bedway grinders and keep them at Brian Bloc's place.
  23. Replies
    58
    Views
    4,072

    There is a oil passage in the apron that lines up...

    There is a oil passage in the apron that lines up with a hole in the top half nut when the half nuts are closed (engaged on the leadscrew). Oil then flows and fills the little reservoir on top of the...
  24. Replies
    19
    Views
    1,599

    My Rivett has been spoken for but the buyer...

    My Rivett has been spoken for but the buyer hasn't come to get it yet.
    He'd better hurry before winter get's here or I might just keep it.
  25. Replies
    5
    Views
    940

    Just want to put a word in here for collector....

    Just want to put a word in here for collector.
    The Holbrook I bought from him/Lenmark was prepared for shipping better than any machine I have ever taken delivery of.
    Lenmark was a pleasure to work...
Results 1 to 25 of 1169
Page 1 of 47 1 2 3 4