Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Bondo

Page 1 of 31 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    12
    Views
    516

    That is the G90 hot dip galvanize. You cant order...

    That is the G90 hot dip galvanize. You cant order g90 unless you are having it hot dipped yourself.

    If you want steel, get zinc plated. That is as close as you can get.

    If you cant order what...
  2. What is the difference from 100 miles to 1,300...

    What is the difference from 100 miles to 1,300 miles. It would still be really bad.

    Now if you take city vs mountains vs flat would be an arguement. I do not like surge brakes in the mountains....
  3. Since the trail gets smaller its definitely a...

    Since the trail gets smaller its definitely a timing issue on the jet. You will have to figure out if it is in the programming or inside the system sonewhere.

    Sent from my SM-G960U using Tapatalk
  4. Replies
    7
    Views
    434

    I have 3 digital elite and 1 elite helmet myself....

    I have 3 digital elite and 1 elite helmet myself. They range over 10 years.

    The shades on all 4 of them are basically the same with just a tiny bit of difference in 1 being a tad lighter but not a...
  5. Thank you everyone for your feedback. I am going...

    Thank you everyone for your feedback. I am going to be researching some of these replies to get what I'm looking for.

    Sent from my SM-G960U using Tapatalk
  6. Key locks, looking for a good security interchangeable core

    Since I do shop, field, contract work, and have a lot of equipment on trailers, I'm looking for a quality padlock with interchangeable cores so I can key different items to certain people.

    I've...
  7. Replies
    11
    Views
    847

    If you dont want to add items like a Pittsburg...

    If you dont want to add items like a Pittsburg seam, then you are limited to clips and epoxy it seems.

    Sent from my SM-G960U using Tapatalk
  8. Replies
    31
    Views
    2,057

    You can search the forum and I am sure you will...

    You can search the forum and I am sure you will find a thread where someone says a spider crawled inside there when the torch was just sitting around and melted to the head.

    Sent from my SM-G960U...
  9. Replies
    12
    Views
    1,027

    I buy the screw jacks off amazon. I just got some...

    I buy the screw jacks off amazon. I just got some of the big red ones, been using them for many years to put machinery on dollies

    Sent from my SM-G960U using Tapatalk
  10. Replies
    31
    Views
    2,057

    Big thing people dont realize is the CK collects...

    Big thing people dont realize is the CK collects can screw deep into torches and block the gas path. To solve this, you have to screw the gas cap in all the way, then screw the collet in, then lock...
  11. Replies
    14
    Views
    832

    You can tap with a NPT tap and just ho in as far...

    You can tap with a NPT tap and just ho in as far as you want to the threads bottom out so it is a flush installation. Or you can go all the way through with the tapered tap and make straight threads....
  12. That helps, and makes a lot of sense now. It...

    That helps, and makes a lot of sense now.

    It depends on the strength needed. If it's just turning a light load. You could do shear pins. But if you are doing a heavy load with minimal angular...
  13. Are they the same shaft knuckles? Then you can...

    Are they the same shaft knuckles? Then you can just change out the knuckle and be done.

    It seems as you want to add in a shear pin in between the knuckles to connect both different PTO shafts....
  14. Dont understand why this posted in 2 different...

    Dont understand why this posted in 2 different sections.

    Sent from my SM-G960U using Tapatalk
  15. Just take a steel block, about 2" x 2" x 4-6"...

    Just take a steel block, about 2" x 2" x 4-6" long, hold it against the inside or outside of the part. Hit the part with your hammer against the block.

    It wont be perfect, but it will look pretty...
  16. I dont see a problem with tapping them in, but at...

    I dont see a problem with tapping them in, but at 1 1/4" black pipe, 4 reducing Ts and 4 close nipples at home depot is like $30. Those wont be hard to line up when they are all together.

    You...
  17. Looking for assistance purchasing from a distant used equipment dealer

    I'm looking at a CAT model E8000 electric 8,000# lift from a company called Material Handling Wholesale Corp in Elgin, IL. It is a refurbished lift without a 48v charger which I assume they will sell...
  18. Replies
    16
    Views
    1,622

    Cant you just use a 3/4 to 1/2 reducer? Sent...

    Cant you just use a 3/4 to 1/2 reducer?

    Sent from my SM-G960U using Tapatalk
  19. It actually looks like a sewer/water key for city...

    It actually looks like a sewer/water key for city water supply.

    Sent from my SM-G960U using Tapatalk
  20. I don't believe alum would be strong enough. I...

    I don't believe alum would be strong enough. I would build it from stainless or steel.

    Sent from my SM-G960U using Tapatalk
  21. Replies
    13
    Views
    1,303

    I build my own curtains and I use yellow. It...

    I build my own curtains and I use yellow. It works ok, but they dont hold up to grinding sparks in heavy use area.

    Yellow works best to see what is going on in the other side, but blue would be ...
  22. Due to the pandemic, I have been getting more...

    Due to the pandemic, I have been getting more sheets of stainless with more stress inside them. So the are perfectly flat at 4' x 10' but when I shear it to 3' x 7' it has a large bow to it.

    If...
  23. Replies
    6
    Views
    989

    5' x 10' is common but not always in 16ga. Some...

    5' x 10' is common but not always in 16ga. Some places and probably more now die to the pandemic just cant stock every size.

    Also see if they would have a 5' x 8'

    Sent from my SM-G960U using...
  24. Replies
    21
    Views
    2,073

    A lot of bad things will probably happen in areas...

    A lot of bad things will probably happen in areas you dont want them to happen in.

    That's why companies dont offer solutions like this.


    There is dual tig torch switch which is common and...
  25. Replies
    46
    Views
    3,085

    I plan on doing this on the floor with it sitting...

    I plan on doing this on the floor with it sitting on 6x6. The horses we have will easily support this plate, but it would be easier to do it on the floor.

    Sent from my SM-G960U using Tapatalk
Results 1 to 25 of 755
Page 1 of 31 1 2 3 4