Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: SBLatheman

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    5
    Views
    762

    I have a manual. Send me an email Ted...

    I have a manual.
    Send me an email
    Ted
    [email protected]
  2. Replies
    25
    Views
    1,513

    I installed the motor and all the wiring on the...

    I installed the motor and all the wiring on the machine today. Smooth and quiet :)
    ...but, as luck would have it, forward/reverse is backwards :rolleyes5:
    I assume I need to switch the red and...
  3. Replies
    25
    Views
    1,513

    Eureka ! ! That worked :o Thank you very much,...

    Eureka ! ! That worked :o
    Thank you very much, Allan, you certainly know what you are talking about :)
    Thanks again,
    Ted
  4. Replies
    25
    Views
    1,513

    More info: The brown goes to the centrifugal ...

    More info:
    The brown goes to the centrifugal switch
    The black wire goes to the capacitor
    Red goes into the windings, and so do the yellow ones.

    Thanks for everybody’s help :)
    Ted
  5. Replies
    25
    Views
    1,513

    I had time this morning to wire it up.(on the...

    I had time this morning to wire it up.(on the bench)
    Flipped the switch on direction and the motor started right up, a little rough running. Shut it off and flipped it the other direction. It...
  6. Replies
    8
    Views
    537

    It is a D1-8...that was the only spindle nose...

    It is a D1-8...that was the only spindle nose offered.
  7. Replies
    25
    Views
    1,513

    Thank you, Allan. That is a very elegant...

    Thank you, Allan. That is a very elegant solution...if it works:)
    I will test the capacitor like you suggested first and let you know how it worked out.
    Regards,
    Ted
  8. Replies
    12
    Views
    541

    I thought that machine looked too big to be a 13”...

    I thought that machine looked too big to be a 13” :skep:
    It is a 16”, as shown by the index plate
    Ted
  9. Replies
    25
    Views
    1,513

    They are pretty good pictures, but they don’t...

    They are pretty good pictures, but they don’t post very well:confused:
    I can email them to you.
    Ted
    [email protected]
  10. Replies
    25
    Views
    1,513

    Wiring motor/switch help...Please

    Wiring motor/ switch help...Please

    This motor is on a Heavy 10 that I bought. The previous owner had replaced the 3-phase motor with this Dayton, wired to just run forward(220v 1-phase). I want it...
  11. Replies
    5
    Views
    762

    The CS33 was made in Spain by METOSA. South Bend...

    The CS33 was made in Spain by METOSA. South Bend imported them for a few years, then Clausing picked them up. You should be able to get parts from them.
    (I still have a few parts)
    Ted
  12. Replies
    17
    Views
    775

    The wiper retainers you have are not for the...

    The wiper retainers you have are not for the Heavy 10. I don’t think they are South Bend.
    Ted
  13. Replies
    2,286
    Views
    442,842

    Sticky: Steve, This machine is a horizontal drive. I...

    Steve,
    This machine is a horizontal drive. I don’t think the bench is original.
    Ted
  14. Replies
    34
    Views
    2,594

    I have a N.O.S. replacement TS spindle for the...

    I have a N.O.S. replacement TS spindle for the 16” for sale.
    It is the high dollar hardened and ground option(the ID and threads are hard, not the OD)
    It has a few pits from a little rust it had....
  15. Replies
    1
    Views
    570

    Send me an email :typing: Ted [email protected]

    Send me an email
    :typing:
    Ted
    [email protected]
  16. Replies
    1
    Views
    475

    I have a 6” Bison adjust tru chuck back for sale...

    I have a 6” Bison adjust tru chuck back for sale (A1-5)...$75 plus shipping
    Email if interested.
    Ted
    [email protected]
  17. Replies
    3
    Views
    764

    The brake is controlled by a TDR (time delay...

    The brake is controlled by a TDR (time delay relay)...yours is probably bad.
    Ted
  18. Replies
    2
    Views
    636

    That is a 9” serial number. Ted

    That is a 9” serial number.
    Ted
  19. Thread: old newbie

    by SBLatheman
    Replies
    1
    Views
    484

    Pretty good chance 😁 Send me an email. Ted...

    Pretty good chance 😁
    Send me an email.
    Ted
    [email protected]
  20. For the record: Volitan purchased the smaller of...

    For the record: Volitan purchased the smaller of the two springs I have.
    The large one is still available in case someone is searching for one in the future.
    Thanks,
    Ted
  21. Yes, see pictures. The first one is about 4 1/4”...

    Yes, see pictures.
    The first one is about 4 1/4” diameter .038” x 1”
    The second one is ~3 1/4” diameter .035”x 1”
  22. I have a couple different return springs for a...

    I have a couple different return springs for a Johansson. N.O.S.
    SEND ME AN EMAIL:typing:
    Ted
    [email protected]
  23. Replies
    9
    Views
    1,654

    I do not have a General Notice reguarding the...

    I do not have a General Notice reguarding the catalog numbers ☹️
    Ted
  24. I have a steady rest for sale. Send me an email...

    I have a steady rest for sale.
    Send me an email :typing:
    Ted
    [email protected]
  25. Replies
    9
    Views
    1,654

    Steve, Are you sure about that ? I have a CL...

    Steve,
    Are you sure about that ?
    I have a CL 187 from the 80’s that is a D1-4
    I had a threaded spindle 10L that was a CLC187
    :confused::confused:
    Ted
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4