Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Booze Daily

Page 1 of 58 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    80
    Views
    3,100

    I have a small rack about 3'x4' by the back door...

    I have a small rack about 3'x4' by the back door that I keep filled.
    But for the big pile, just square the ends off by alternating directions each layer. No rack needed.
    Definitely keep it off the...
  2. Replies
    18
    Views
    841

    I’d be more worried about all the chips you’ll be...

    I’d be more worried about all the chips you’ll be recutting and having to finish the cavity a second time to get rid of the funkiness.
  3. Been doing it for years. I usually clear the...

    Been doing it for years. I usually clear the flutes behind the tip so they don’t rub.
  4. Thread: Chip fan

    by Booze Daily
    Replies
    16
    Views
    682

    I love the kettle cooked ones.

    I love the kettle cooked ones.
  5. Replies
    79
    Views
    3,098

    Life is like a roll of TP. The closer you get...

    Life is like a roll of TP.
    The closer you get to the end, the faster it goes.
  6. Replies
    40
    Views
    1,498

    These guys sell HSS inserts that fit std...

    These guys sell HSS inserts that fit std toolholders. I've never used them, but maybe there's something you could use.

    Standard and Specialty Inserts
  7. Replies
    207
    Views
    21,962

    My allergies have lessened over the years but I...

    My allergies have lessened over the years but I get a nasty reaction to bee stings. Especially yellow jackets.
    Claritin is the only thing that works for me and doesn’t make me drowsy.
    NyQuil. Now...
  8. Do you have the manual? Haas has all kinds of...

    Do you have the manual? Haas has all kinds of drilling cycles just by adding variables to your canned drilling cycles.
  9. Replies
    1,113
    Views
    299,972

    What happened to his other foot?

    What happened to his other foot?
  10. Are you using the same post on the new and old...

    Are you using the same post on the new and old machines?
    What does your lead-in and lead-out code look like?
  11. If you are changing your work offset you need to...

    If you are changing your work offset you need to re-call it for the control to pick up the change.
    If you are changing the tool length offset you need to re-call it to pick up the change.
  12. Replies
    29
    Views
    1,404

    I have an old cabinet hanging on the wall that I...

    I have an old cabinet hanging on the wall that I store mine in. The tools that don't have cases, that is.
    The stuff in smaller cases like my brad nailer, laser level, etc. fit on top.
    Bigger stuff...
  13. I have an Okuma ES-L8 that fits that description.

    I have an Okuma ES-L8 that fits that description.
  14. G00 G43 H1 Z.1 should stop .100 above Adjust...

    G00 G43 H1 Z.1 should stop .100 above

    Adjust your offset, rerun the above. Should change where it stops.
  15. I only run CNCs these days.

    I only run CNCs these days.
  16. I used to run one of those. It was the best...

    I used to run one of those. It was the best engine lathe I've ever run.
  17. This is absolutely no help to the OP but reminded...

    This is absolutely no help to the OP but reminded me of a funny story.

    I had an operator work for me one summer. The lathe threw a low lube alarm. He thought that meant it needed coolant.
    So he...
  18. Replies
    24
    Views
    1,207

    Check #3020-#3025. System Variables | Customer...

    Check #3020-#3025.
    System Variables | Customer Resource Center
  19. Replies
    20
    Views
    973

    Sounds like more than $300 worth of figuring....

    Sounds like more than $300 worth of figuring.
    I'd buy the tool.
  20. Replies
    30
    Views
    1,228

    Why's that? I've changed mine several times, but...

    Why's that? I've changed mine several times, but I don't know if I touched the stylus or not.
  21. Replies
    30
    Views
    1,228

    Check the batteries.

    Check the batteries.
  22. I don’t mind. The owner and his employees are...

    I don’t mind. The owner and his employees are just trying to stay afloat.
    Just like me.
  23. Replies
    14
    Views
    1,005

    That’s really nice. You should see my machines....

    That’s really nice. You should see my machines. And I bought them brand new.
  24. Nope. We usually go to the little ma and pa...

    Nope. We usually go to the little ma and pa places in town.
    Burger, fries, couple beers for me and the wife.
    Used to be about $35 after tip. Now it's about $43 after tip.
  25. Replies
    17
    Views
    809

    The ones I have seen all have proprietary thread...

    The ones I have seen all have proprietary thread forms, I guess to differentiate themselves from the competition.
Results 1 to 25 of 1438
Page 1 of 58 1 2 3 4