Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: triumph406

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    126

    If your tapping plastic you could make a tool...

    If your tapping plastic you could make a tool from steel on a lathe and cut flutes on a mill, obv assumes you have a lathe and mill.
  2. The OP is talking about profiling, it's not going...

    The OP is talking about profiling, it's not going to effect Z height if you CS at the correct Z position
  3. Well IKEA allows people with limited means to buy...

    Well IKEA allows people with limited means to buy and assemble decent furniture. So if your a student IKEA, on a fixed income etc IKEA can be a very viable method of buying furniture. Their meat...
  4. Replies
    777
    Views
    51,097

    737-666 There you go

    737-666

    There you go
  5. Replies
    42
    Views
    3,837

    Presumeably the male/female splines have a...

    Presumeably the male/female splines have a specific orientation that needs to be maintained
  6. Clever idea!

    Clever idea!
  7. Replies
    44
    Views
    2,760

    You want to put the level across the crown of the...

    You want to put the level across the crown of the front/back ways. Check for any dings that might hold up the level. Stone those of if required.
  8. Replies
    44
    Views
    2,760

    How are you measuring the twist?

    How are you measuring the twist?
  9. I use TrimSol 585XT, it can sit for months...

    I use TrimSol 585XT, it can sit for months without degrading, that's with/without an aerator.
  10. Replies
    57
    Views
    15,294

    As long as I can get YG-1 Alu-power end mills at...

    As long as I can get YG-1 Alu-power end mills at good prices, I couldn't care less where the carbide comes from or where their ground.
  11. New or used?

    New or used?
  12. Replies
    777
    Views
    51,097

    Increasingly, the iconic American planemaker and...

    Increasingly, the iconic American planemaker and its subcontractors have relied on temporary workers making as little as $9 an hour to develop and test software, often from countries lacking a deep...
  13. Replies
    46
    Views
    2,877

    I've been using Cadkey99 since 1999, still use it...

    I've been using Cadkey99 since 1999, still use it every day, as do others.
  14. Replies
    19
    Views
    11,762

    I use fly cutters all the time. This flycutter...

    I use fly cutters all the time. This flycutter misinformation is put out by people who either don't know what their talking about or have never seen a Bridgeport.

    I use a BP multiple hours a day 6...
  15. Replies
    777
    Views
    51,097

    So you don't think Boeing should have caught this...

    So you don't think Boeing should have caught this before the FAA?

    So what happens if Boeing doesn't test every scanerio, then the FAA does a substandard review and misses a few aspects of the...
  16. I would be interested in ring gages from .3"-1.5"...

    I would be interested in ring gages from .3"-1.5" dia
  17. Replies
    777
    Views
    51,097

    You mean it's upto the FAA to try unlikely...

    You mean it's upto the FAA to try unlikely scenarios to test the airworthiness of Boeings aircraft.

    I think maybe Boeing should have been doing that, before and after 2 planes crashed.

    You do...
  18. Replies
    777
    Views
    51,097

    Claims of Shoddy Production Draw Scrutiny to a...

    Claims of Shoddy Production Draw Scrutiny to a Second Boeing Jet - The New York Times


    But several former employees said high-level managers pushed internal quality inspectors to stop recording...
  19. off your meds again?

    off your meds again?
  20. well the 2 gunsmith friends have grown up around...

    well the 2 gunsmith friends have grown up around guns their whole lives, so were well versed and immersed in gun culture, the cardinal no1 rule being safety around guns, so you or your loved ones...
  21. Replies
    777
    Views
    51,097

    United extends ban on Boeing 737 Max after...

    United extends ban on Boeing 737 Max after regulator finds new problem | Business | The Guardian

    United Airlines has become the latest carrier to extend its ban on using the Boeing 737 Max after...
  22. I have 2 friends who are gunsmiths who will under...

    I have 2 friends who are gunsmiths who will under no circumstances have anything to do with AR15 or similar work, or the people who want it done.

    They don't like the typical AR15 user/customer,...
  23. If you had (or access to) UG NX you can import a...

    If you had (or access to) UG NX you can import a *.txt file into a file as points or create a spline using the points.

    If you had Cadkey there's a way of editing the excel file so it can be read...
  24. Replies
    13
    Views
    1,920

    I have a Sag14, when you connect the power to the...

    I have a Sag14, when you connect the power to the machine, you have to make sure you can feel pulsations in the clear window of the lube indicator (top right hand side of headstock). That means the...
  25. Replies
    777
    Views
    51,097

    Here you go, another problem you need to try and...

    Here you go, another problem you need to try and solve here.

    Boeing Reports Zero New Plane Orders For Second Straight Month | HuffPost
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4