Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: sudsy55

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    258

    Can't you rotate the axis in Mazatrol?? I'm not...

    Can't you rotate the axis in Mazatrol?? I'm not familiar with that control and haven't done 4th axis work yet
  2. Replies
    6
    Views
    258

    I don't know if this would work for what you are...

    I don't know if this would work for what you are wanting to do but worth a try. Use the priority numbers in the mazatrol program. Number each tool in the order that you want them to do work. Like I...
  3. Replies
    7
    Views
    595

    I copied the opton parameters for my lathe. Not...

    I copied the opton parameters for my lathe. Not sure if it has EIA as I haven't got it powered up but will get them to you to compare with yours.
  4. Replies
    7
    Views
    595

    Not bad money for changing a few numbers

    Not bad money for changing a few numbers
  5. Replies
    11
    Views
    738

    The motors are fairly easy to get at. Just take...

    The motors are fairly easy to get at. Just take the covers off the back and you can see the motors and the belt
  6. Replies
    7
    Views
    595

    I may be totally wrong here but I was doing some...

    I may be totally wrong here but I was doing some reading about options on my M32 and to me it looked like if you had a certain board with some options installed (can't remember which one offhand) the...
  7. When you are trying to home it are you pressing...

    When you are trying to home it are you pressing the - or + direction. Normally needs to be the -
  8. Replies
    24
    Views
    1,683

    I'll take the level if you will ship to Australia...

    I'll take the level if you will ship to Australia 5411. Let me know the cost and email address
  9. M32 is Mill and T32 is lathe as has already been...

    M32 is Mill and T32 is lathe as has already been mentioned. It may have the EIA option to program G % M code as well as conversational
  10. Replies
    6
    Views
    468

    Swap the drives between the axis's. If the alarm...

    Swap the drives between the axis's. If the alarm follows the drive its a drive fault. If it stays with the same axis it's probably and encoder fault
  11. Replies
    13
    Views
    589

    The one on the motor is a tach generator. The one...

    The one on the motor is a tach generator. The one on t he end of the ballscrew is the encoder. My understanding of servo lag is when the signal to move is given but not excecuted in an given time....
  12. Replies
    11
    Views
    672

    I think that the last digits probably only relate...

    I think that the last digits probably only relate to maybe location of manufacture or date or something similar. Just check that all the jumpers and little switches are set the same as yours before...
  13. Multi is in the first line of your program

    Multi is in the first line of your program
  14. Yes I would have thought that the circuit board...

    Yes I would have thought that the circuit board schematics should be available once they stop servicing or supplying them.
  15. You can just move your WPC and copy the program...

    You can just move your WPC and copy the program 42 times. Maybe use the multi part and move the WPC and copy 9 times with a program change to 2 on the last to get the exact amount of parts you need....
  16. Replies
    8
    Views
    860

    Have you done a re-initialise? You will lose all...

    Have you done a re-initialise? You will lose all your data and programs but would be the first thing to do before spending $$$ on other boards
  17. Replies
    6
    Views
    833

    Still here

    Still here
  18. Replies
    1
    Views
    516

    Most of those chargers shut down when fully...

    Most of those chargers shut down when fully charged and should kick back in when the voltage gets down to a certain amount
  19. When I was 13 or 14 my old man brought home an...

    When I was 13 or 14 my old man brought home an old South bend lathe. Once we cleaned it up and got it working I played around till I got the hang of it then started making extra wide slot car wheels...
  20. Replies
    23
    Views
    2,146

    I think the last bit should be the other way...

    I think the last bit should be the other way around. I would rather be dead than brain dead
  21. Here it is. The pages aren't in order but they...

    Here it is. The pages aren't in order but they are numbered at the bottom

    Dropbox - 408 Error clear.doc - Simplify your life
  22. I do have that procedure somewhere. I will have...

    I do have that procedure somewhere. I will have to find it.
  23. Replies
    6
    Views
    833

    Still looking

    Still looking
  24. Replies
    6
    Views
    833

    Anyone ?????:willy_nilly:

    Anyone ?????:willy_nilly:
  25. Replies
    6
    Views
    833

    254682 This is the culprit

    254682

    This is the culprit
Results 1 to 25 of 391
Page 1 of 16 1 2 3 4