Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: drylakemachine

Page 1 of 21 1 2 3 4

Search: Search took 0.01 seconds.

  1. really portable or using a mill to drive the bar?...

    really portable or using a mill to drive the bar? I have access to plans for a bar set up ,you just need to figure bar and cat head sizes.
    W
    I'd go vertical CNC profile the dia's.
    jim
  2. Replies
    0
    Views
    512

    wtb nut for a 5c h-v indexer

    Bought a no name 5c hv indexer and can only get about a half thread to engage and then cant lock it.
    Anybody got one about 5 1/2 inches long?
    jim
  3. Replies
    99
    Views
    6,891

    Ran one back in the day. 48 incher raised 24 ,...

    Ran one back in the day. 48 incher raised 24 , installed a 96 inch face plate, had a lever clutch. Did turn much in high gear.
  4. 17-4 drilled hole in threads can I use a tumbler?

    Can I use a tumbler to get rid of a burr left by drilling a 1/8 hole thru a .750 dia. into a 5/8 18 threaded bore without destroying the thread quality? Matl 17-4 ss
    I run a tap down just past the...
  5. I found a manual for my machine GAMA 33 sp ,early...

    I found a manual for my machine GAMA 33 sp ,early 60's model.There is a trouble shooting page for the Hi frequency mode.
    PM me your email and I'll take pictures and send those pages .
  6. I think I have the same machine in storage, I'll...

    I think I have the same machine in storage, I'll check in AM
    JIM
  7. Replies
    7
    Views
    746

    Hi Chris I tried this earlier on my phone ,It...

    Hi Chris I tried this earlier on my phone ,It didn't work.My motor shaft is 1.125 .My major problem is the keyway on the OD of the motor half.
    If can PM me pictures and price.
    Thanks Jim
  8. Replies
    7
    Views
    746

    My bad ,Thought 6913 would be enough and only...

    My bad ,Thought 6913 would be enough and only folks that knew what it was would respond. Also a 5913 pulley system might work.
    Thanks Packard bill for clearing(no pun intended) it up.
    Jim
  9. Replies
    7
    Views
    746

    WTB 6913 VS pulley

    I posted in parts ,no luck yet, hoping to find someone that had changed to VFD and had removed the pulleys.
  10. Replies
    46
    Views
    5,127

    Always in neutral.my buddy has the same lathe as...

    Always in neutral.my buddy has the same lathe as I.I went to use his and the lever just moved up and down,mine engages with lever movement.
    There is an adjustment to disengage lever so it has to be...
  11. I have a 60 inch will need to dig it out to check...

    I have a 60 inch will need to dig it out to check brand and length.
    jim

    your pm box is full.
  12. Replies
    1
    Views
    567

    WTB clausing 6913 motor pulley

    WTB 6913 motor pulley half of the variable drive.Complete unit if the price is right.
  13. Replies
    12
    Views
    1,545

    If you have the connection( 16)and ( 18 a&b ) and...

    If you have the connection( 16)and ( 18 a&b ) and there is room to enlarge the major dia.you do that first then over size a new screw out of 4140.
    If that is not possible ,then I would bore the...
  14. Replies
    15
    Views
    1,309

    Finditparts.com best prices I could find.

    Finditparts.com best prices I could find.
  15. 4000 # before the chuck guarding

    4000 # before the chuck guarding
  16. Replies
    4
    Views
    617

    New or new to you? Are the rest of the cuts burr...

    New or new to you? Are the rest of the cuts burr free?
    I'd put pieces of paper along the cutting edge and adjust until you get a clean cut.

    Jim
  17. Replies
    5
    Views
    1,505

    What are X&Y and footprint? thanks jim

    What are X&Y and footprint?
    thanks jim
  18. Had the same problem, cataract surgery took...

    Had the same problem, cataract surgery

    took care of it.

    jim
  19. Replies
    8
    Views
    761

    I've got a 3 hs broke down to sub assemblies ....

    I've got a 3 hs broke down to sub assemblies . The stator needs new leads.
    Not sure if this will interchange with a 3ch.
    jim
  20. Replies
    12
    Views
    1,437

    Sounds like a knife and dog release .In my...

    Sounds like a knife and dog release .In my thought a counter weight wouldn't
    help as the clutch engages at different points.
    Taking weight off the ram and adding a counter balance, plus trouble...
  21. catalina cylinders in garden grove ca. They make...

    catalina cylinders in garden grove ca. They make o2 cylinders and can neck down and thread if needed.
  22. Replies
    2
    Views
    668

    3hs 2 sp motor

    I have a 15-30 hp motor and rpm's are 3600 and 7 200, Question is how does that work with only 3 wires feeding it.
    Thanks jim
    No panel or wiring diagram came with the machine.
  23. Replies
    8
    Views
    1,391

    3 hs in need of a stator

    I didn't get any hit's in the for sale forum on my 3hs, so It's now down to sub assembly. The way's and gearing all look ok.
    The reason for getting rid of it, 1 no panel with it 2 15-30 hp motor...
  24. Replies
    23
    Views
    4,333

    Chrome and grind will work. You may have to make...

    Chrome and grind will work. You may have to make a mandrel if the C&G shop doesn't have one.
  25. If your close to indy you might try some of the ...

    If your close to indy you might try some of the nhra race shops in that area.
Results 1 to 25 of 502
Page 1 of 21 1 2 3 4