Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: bradinNC

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    1,662

    Move to Missouri on hold/ lathe no longer for sale

    Move to Missouri on hold/ lathe no longer for sale
  2. Replies
    3
    Views
    1,662

    Thank you John.

    Thank you John.
  3. Replies
    3
    Views
    1,662

    1941 American pacemaker/ 18x54

    I am relocating to Missouri and have decided to sell my big lathe. 18 x 54, feed stops for both axis,M5,
    15 hp motor replaced with new 5 hp Baldor 3 ph. Great candidate for restoration.Has original...
  4. Replies
    14
    Views
    5,873

    What a fantastic tree for a hedge! Wonderful to...

    What a fantastic tree for a hedge! Wonderful to keep pesky bad guys out!
  5. Replies
    20
    Views
    4,446

    Was cleaning up the rest of the booty and...

    Was cleaning up the rest of the booty and realized this is probably part of the tailstock and dividing head.

    169550
  6. Replies
    20
    Views
    4,446

    I brought this head home with another head...

    I brought this head home with another head (Ellis) and a tailstock. Looking at the diagram I just realized I have the matching tailstock to the toolmaster dividing head .So I'm a happy camper today!...
  7. Replies
    20
    Views
    4,446

    It does have a pattern on the backside. 11 rows...

    It does have a pattern on the backside. 11 rows on front,back is partially obscured by a collar but looks to be 11 also.
  8. Replies
    20
    Views
    4,446

    Thanks Mike, that is a HUGE help. Now I'm not in...

    Thanks Mike, that is a HUGE help. Now I'm not in the dark! Brad
  9. Replies
    20
    Views
    4,446

    Thank you Mike. That's a big help. I would like...

    Thank you Mike. That's a big help. I would like to find an exploded diagram of this dividing head.
    thanks again, Brad.
  10. Replies
    20
    Views
    4,446

    Thanks Larry. Just went out to shop and checked...

    Thanks Larry.
    Just went out to shop and checked a few items. The cover is held on by 5/16-18 screws.The 4 big bolt holes are 1/2-13 with 2
    5/8" spacing. Keyway is 5/8 wide and 5/16 deep with...
  11. Replies
    20
    Views
    4,446

    Disk diameter is 6.75 inches. ...

    Disk diameter is 6.75 inches.

    168628168629168630

    I just spotted the stamped number in the top middle picture, but I don't think it's significant.
  12. Replies
    20
    Views
    4,446

    unknown dividing head

    I can't seem to find any markings on this. If I could get an idea what manufacturer built this it sure would help. Pretty sure its a taper 40. I've got the handle soaking in solvent.


    ...
  13. I like to keep a set of CHEAP drill bits on hand...

    I like to keep a set of CHEAP drill bits on hand for loaners. I never loan out my good tools to workers outside the mold shop.
  14. Or some moron sneaking up while I'm taking the...

    Or some moron sneaking up while I'm taking the last tenth off a pin I'm grinding.
  15. Replies
    19
    Views
    2,977

    Apparently decimal points are not considered very...

    Apparently decimal points are not considered very important, or he is just not realistic. That lathe is barely above scrap value at best.
  16. Replies
    62
    Views
    12,161

    My mistake. Sure is a good looking lathe. Looks...

    My mistake. Sure is a good looking lathe. Looks like it has a good home now!
  17. Replies
    21
    Views
    9,782

    The simplest way I can explain, is to turn...

    The simplest way I can explain, is to turn opposite sides an equal amount. For instance, you have the part in the chuck snugged up. If you want to shift in a certain direction, loosen the side you...
  18. Replies
    62
    Views
    12,161

    Hope you didn't damage anything lifting by the...

    Hope you didn't damage anything lifting by the chuck. Manual for my 1230 Nardini says to lift thru webbing in between the ways. Very good looking lathe. Looks like it was just a little dirty and...
  19. Replies
    108
    Views
    12,841

    That list is rather demanding. If you are dead...

    That list is rather demanding. If you are dead set on that school, go for it. But I'd get some references from past graduates. I finished tool/die school 2 yrs ago, stretched out over 5 or so years...
  20. I'm not seeing much rebar in the visible...

    I'm not seeing much rebar in the visible concrete. Looks like somebody cut corners. But eventually those vettes would be toast.
    Shame about the oldie on top, those silly newer versions can just sit...
  21. Replies
    9
    Views
    1,425

    Sounds like you got a free 1 phase motor and are...

    Sounds like you got a free 1 phase motor and are limited on funds. You can "get by" with the 1 phase as mentioned above, with exception of other motors on lathe.
    But don't toss your old motor. Very...
  22. Replies
    86
    Views
    13,733

    I think most here try to steer clear of projects...

    I think most here try to steer clear of projects that show lots of red flags. Most older guys don't like to use valuable time on questionable machines. Because the older you get, the more value time...
  23. Replies
    19
    Views
    4,087

    A friend of mine insulated his ceiling in a...

    A friend of mine insulated his ceiling in a similar building using foiled sided foam panels (celotex?) I think they used purlins and secured panels to that. His heating bill went way down, and I...
  24. Replies
    296
    Views
    26,324

    That may be your opinion but I believe we are...

    That may be your opinion but I believe we are experiencing different results. No or little ambition to learn English, poor discipline of their offspring, don't respect American citizens, hooking up...
  25. Replies
    78
    Views
    9,050

    Old trappers trick: soak your traps in water with...

    Old trappers trick: soak your traps in water with some walnut shells, water turns blackish, will de-scent your traps effectivly. And it's cheap. Look for food sources in your shop you may have...
Results 1 to 25 of 112
Page 1 of 5 1 2 3 4