Search:

Corn cob face mill as big as your lowest speedsetting alows
Ideal would be the wide of the slot
2 passes to get to depth with feed that does not stop the motor or damage the mill Low then
Slow...

That shear has a lott to endure then :D

Peter

Papershear then

Peter

I know these french fuses 10X32MM isn't it They cost aarm and leg over here The ones in the picture just peanuts
Peter

Before using it I would get those galled places smoothend Make sure all somewhat loose particals are removed
But its a perfect candidate for SKC 63R A slideway compound for repairs, I have used it...

Not when it matters That is while cutting Then the 2 pieces are still one piece (Does that makes sence:D)But anyhow the gap setting is still the same percentage
One can check the cutting edge 1/3...

I have the German manual in PDF
Send me a PM with your e-mailadres and you get a wetransfer link from me

Peter

Make sure to fill the keyways one way or the other
The couplings will dig in otherwise
There are more brands of keyless couplings
Google for clamping elements or clamping bushes One can put 2...

Gap is 5% of sheetthickness So for 10mm sheet the gap is 0.5mm
Will that cut paper ??
For 3mm it is 0.15mm
What gap you need to cut paper??

Peter

To the OP
You said you placed oak boards between the machine and forks
Oak is a hard wood. I want something to dig in
A softer wood or better a sheet of rubber
If you move machines on a...

Gears are too cheap to 3-D print

Peter

Thats why I prefer to modify a steady that is on the low side for the intended lathe Just mill some flats on the underside and bolt on a subplate
And if the total wide is about the same as...

Do the jaws originaly belong to the chuck
If replacement jaws were bought at some time these may be a bit stiffer Stone the surfaces with a diamond stone then The trick is to find out which...

Like said before Mill the bottem flat and ad a subplate Or better prehaps Mill a groove and bolt a block with a V to it
Even if the steady ends up a bit high it does not matter to much

Peter

I have some collets with a extended nose The extension has a radius These are for hobbing
To grip the workpiece closer to the hob

Peter

you can bolt 2 of them together and/or mount 2 of them on the same hub to get a thicker gear
I would make a hub with a flange between the 2 gears and bolt the gears on the flange
This one is...

Oke
A shear with a 20mm capacitiy you set the gap to cut paper the same as one that cuts 0.1mm???:willy_nilly:

Peter

I vote for a 1ph input 3ph output VFD as well
The motor fits already ,runs smoother and will not draw that much amps at start-up wen set properly
If the voltage does not match one can use a 1ph...

I see them with a plain back
So you can mount it on a din55022 backplate

Peter

You send me a request through Werktuigen - koop of verkoop nieuwe en gebruikte machines + gereedschappen | Werktuigen.nl

Peter

Yes Level as a way to get the machine square in all directions
Check the gap again and make the gap bigger to start with as the gap might have been narrowed and knifes might hit oneanother
Had a...

The surface it will be looking at needs to be protected from swarf wear and dust So you end up with a box with a small camara inside So a scale like thing anyhow

Peter

More to see on his Ebay site
You mean this one?? I do not have one right now
Alu Deckel ( Riemenschutz) fur Schnellaufkopf Deckel Frasmaschine | eBay

Peter

Can`t you buy a stock plastic gear Works as well

Peter

You did send me a e-mail already
Do you have the old model high speed head with 16mm collets or the newer one with NT40
If I know I can see tomorrow if I can help then

Peter