Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: ryanbcnc

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    35
    Views
    2,417

    I have been in situations like this multiple...

    I have been in situations like this multiple times and its beyond annoying. We actually cut ties with a tooling company .. no names but starts with a K. Due to the sales team being so cocky and...
  2. Replies
    750
    Views
    479,275

    Sticky: As stated before they do not offer an extension...

    As stated before they do not offer an extension for local variables. I assume this is because they correspond to letters for the Macro call. In that case I think you have the best set up calling them...
  3. Replies
    31
    Views
    3,089

    I had the same issue with an outrigger on a...

    I had the same issue with an outrigger on a boring mill a couple years back .. the gouges were more like .06 deep, I replaced the turcite and filled the gouges with epoxy. still going with no issues...
  4. Replies
    14
    Views
    2,559

    I am far from an expert on this topic but I did...

    I am far from an expert on this topic but I did just go through the same situation. Due to a lack of upgrade potential on most laptops if you can make due with a Desktop you can probably save some...
  5. Replies
    45
    Views
    6,003

    As already said: higher rpm, cutting fluid, sharp...

    As already said: higher rpm, cutting fluid, sharp tool,and leave more material for your final pass (not to much as depending on the application you could end up out of round. You also may want to...
  6. Replies
    12
    Views
    2,513

    Also interested, subscribing as well.

    Also interested, subscribing as well.
  7. Replies
    4
    Views
    812

    depending on the foot print/weight I would be...

    depending on the foot print/weight I would be interested, pm pictures/details whenever you get a chance, Thanks!
  8. Replies
    14
    Views
    1,393

    If it is pre-hard for the application I would not...

    If it is pre-hard for the application I would not bother trying to harden it further. If your having issues it likely is not pre-hard .. or like some people I work with you need to learn the...
  9. Replies
    4
    Views
    812

    Looking for benchtop universal grinder

    Hi Everyone,

    Looking for a bench top universal grinder. Mostly to re-grind endmills, not too worried about the ability to grind ball nose but that would be a plus. Located north of Toronto but...
  10. Replies
    5
    Views
    1,222

    The company I work for does not have any copys of...

    The company I work for does not have any copys of the ASME standards. More of what I am asking is will I be able to get by with a copy of 14.5 1994 and a write up on the updates in 04 and 2018 or are...
  11. Replies
    5
    Views
    1,222

    ASME Y14.5 .. clarification

    Hi everyone just finishing the final block of my apprenticeship in class. We had a class that focused on GD&T .. the teacher was clearly under qualified to be teaching the subject. For the sake of my...
  12. Replies
    3
    Views
    942

    WTB benchtop surface grinder

    Looking to buy a decent bench top surface grinder. Will be only using it for small projects, grinding set up parts after pre heat etc. Any recomendations? Located In Canada about an hour north of...
  13. Replies
    2
    Views
    1,236

    Mitutoyo 543 Indicators

    Just purchased a used Mitutoyo 543-252b. Trying to find a manual for it. Mitutoyo does not list anything I assume because it is old and discontinued. Anyone have any information on this? Years of...
  14. Replies
    6
    Views
    1,340

    Should have mentioned in the post, that I tried...

    Should have mentioned in the post, that I tried this with no luck
  15. Replies
    6
    Views
    1,340

    Is there a parameter to change this? We have a...

    Is there a parameter to change this? We have a machine with 18i and one with 21i that run the programmed feed rate.. makes things a little easier
  16. Replies
    6
    Views
    1,340

    Fanuc 0i-mf slowing feed rates in helical

    I got a chance to write a program for the companys brand new Kuraki Akb11 and I am running into one problem I can't seem to solve, when running a helical interpolation the feed rate is slowing down a...
  17. Replies
    20
    Views
    1,436

    Its a cat50 bmc with 30hp .. there is a lack of...

    Its a cat50 bmc with 30hp .. there is a lack of thru coolant pressure which wouldn't be helping but for sure not pussy footing on the feed. May try annular cutters next
  18. Replies
    20
    Views
    1,436

    No its not what i consider long either but a...

    No its not what i consider long either but a couple companies offer indexable drills that can go through stacked plates only up to 3xd. As it is a weldment there is hard spots. The spade drill...
  19. Replies
    20
    Views
    1,436

    2" and 1" plates with a total depth around 8.5"....

    2" and 1" plates with a total depth around 8.5". Yes increased production time but because of inconsistencies having issues with carbide breaking. The HSS even with cobalt was needing to be run to...
  20. Replies
    20
    Views
    1,436

    4.5+xD Drilling stacked plate

    I am doing runs of weldments that include drilling 1.875(ish)thru stacked plate. I have been using a 1.875 spade drill but I am looking for another solution. The few modular drills I have found...
  21. Replies
    3
    Views
    529

    Automotive metallurgy reference

    I have been searching for a good reference for metallurgy standards for automotive applications. Things like brake calipers and brake pistons. Looking for something dependable .. not "google it". I...
  22. Replies
    16
    Views
    3,328

    [QUOTE=Hbjj;3097560]If I need a true. 001 fit I...

    [QUOTE=Hbjj;3097560]If I need a true. 001 fit I do a second op
    Like ream or hone
    On the junk I run measuring from the bar to the wall would be inaccurate owing to bar runout/deflection

    In the...
  23. Replies
    16
    Views
    3,328

    Portable line boring measurement

    Was back on the climax portable boring mill yesterday for the first time in a while .. and got to thinking about how ridiculous it is that i am still using spring calipers to measure my bores.. its...
  24. Horizontal mill clocking in bores at a distance

    The Cnc horizontal mill that I run is having some issues (encoders down) with a 6 week wait period turning the mill into a manual mill basically. Once a week I would check x and y axis grid shift by...
  25. Thanks for the info Bill, When you says pc...

    Thanks for the info Bill, When you says pc communication software are you referring to altering settings on my pc or will I need to download specific software for this? (Again sorry for my complete...
Results 1 to 25 of 28
Page 1 of 2 1 2