Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Mskiin

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,824

    The wips keeps deleting on me. And I figured out...

    The wips keeps deleting on me. And I figured out why. If you load a program that uses probing written by CAM software like fusion, for some reason when you delete that program from memory to save...
  2. Replies
    2
    Views
    1,824

    Found it. Settings 7, 23, and 155. Then you...

    Found it. Settings 7, 23, and 155.

    Then you can reinstall the wips sub routines.
  3. Replies
    2
    Views
    1,824

    2 parameters for recovery install?

    My machine deleted the wips sub programs again on me for whatever reason. There are 2 parameters that have to be switched to allow the recovery files to be downloaded to the machine, does anyone know...
  4. Replies
    9
    Views
    2,305

    Yes. So i got the new set screws in and I...

    Yes.

    So i got the new set screws in and I cranked them down, and when I was close to perfect I started cranking the top ones down. Finished the centering and made sure everything was tight, and...
  5. I just had to do this do to a low memory issue,...

    I just had to do this do to a low memory issue, the machine chose to delete somethings that it should not have deleted. There are some parameters you have to switch off to be able to load it all....
  6. Replies
    9
    Views
    2,305

    So my spindle taper is fine and clean. every tool...

    So my spindle taper is fine and clean. every tool repeats with no run out, without using the probe It will go in an out and stay centered. I think the issue is that i'm not tightening them enough....
  7. Replies
    9
    Views
    2,305

    Reinshaw probe tip trouble staying centered

    Hello everyone

    My probe tip seems to be having a hard time staying centered. I took it apart cleaned all the oil that was between the body and the holder and put it back together hoping it solved...
  8. No damage! Recalibrated and probe is fine.

    No damage! Recalibrated and probe is fine.
  9. Thank you all for ther wonderful comments. Ill...

    Thank you all for ther wonderful comments. Ill know tomorrow when the new tip comes in. Thanks again.
  10. How do I disable the button on the control?

    How do I disable the button on the control?
  11. Thank you. I did order a new tip and I threw it...

    Thank you. I did order a new tip and I threw it in with the broken tip, and just checked that it worked in a bore which it does. Bounced back and lightly touched and it set it. I wasn't going to...
  12. Reinshaw probe ejected from spindle, permanent damage?

    Good evening all,

    My wife was talking to me while i was moving my z axis, when i went to hit the other axis button, I accidnetly hit the tool release and ejected my probe onto the table breaking...
  13. Replies
    19
    Views
    1,843

    I purchased a used 2012 Tm2p with 10 tools, wips,...

    I purchased a used 2012 Tm2p with 10 tools, wips, and about 1500 hours on it last year. I love it. I have not been limited yet by the 6k rpm or the 10 tools. I've been machining for 15 years now and...
  14. Replies
    3
    Views
    502

    I did all that again, no change. Then I figured...

    I did all that again, no change. Then I figured out it has to be running a program to recognize the offset In the position window. Once I put g43 h06 then a g01 movement, it picked up the offset and...
  15. Replies
    3
    Views
    502

    WIPS Z touch off problem

    I have figured out how to probe the tools and the part. I went through the calibration for WIPS, and the X and Y gets touched off correctly when probing. But when it probes the Z it sets the G54...
  16. Awesome. That's what I needed. THANK YOU...

    Awesome. That's what I needed. THANK YOU SOOOOOOOOOO MUCH!!!
  17. Using more tools than spots in the toolchanger

    Good evening all,

    I am attempting to touch off more than the 10 tools in my umbrella changer. All of the 10 tools in the changer cycle normally, but I want to use say tool 11, but when I hit M06...
  18. Replies
    2
    Views
    619

    Ok that got me going. Waiting for batteries to...

    Ok that got me going. Waiting for batteries to be delivered. One of the issues the previous machine owner took the batteries out of the tool setter and the probe. The rest of it looks easy. I'll...
  19. Replies
    2
    Views
    619

    2011 Tm2p WIPS instruction

    Good morning

    I am attempting to figure out how to use the wips on my new to me machine. It didnt come with any instruction manuals, and the ones I have found are only for the new control. Any one...
  20. Replies
    3
    Views
    539

    Thanks a bunch! Do you know if the z axis ball...

    Thanks a bunch! Do you know if the z axis ball screw can be rotated by hand with machine unplugged? Or do I need to remove the z motor?
  21. Replies
    3
    Views
    539

    TM2p spindle nose from table distance

    Good afternoon. I've been searching the threads but have not found an answer. I just purchased a used Tm2p. Had a machine inspection done it's good to go. But they did not ship the machine with the Z...
Results 1 to 21 of 21