Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: converterking

Page 1 of 56 1 2 3 4

Search: Search took 0.03 seconds; generated 4 minute(s) ago.

  1. Parts & Smarts at 572 Pine Street, Burlington WI...

    Parts & Smarts at 572 Pine Street, Burlington WI is your best bet for old Bendix and Dynapath controls.
  2. Replies
    69
    Views
    4,721

    And you never will.

    And you never will.
  3. Replies
    69
    Views
    4,721

    I think it's Ball 1

    I think it's Ball 1
  4. Replies
    60
    Views
    3,300

    Same old Gordon.

    Same old Gordon.
  5. Replies
    60
    Views
    3,300

    It would have been very difficult to assemble my...

    It would have been very difficult to assemble my race engines if my micrometers were at my employers shop.
  6. Replies
    60
    Views
    3,300

    I am watching this with interest as I have a 0-6...

    I am watching this with interest as I have a 0-6 set of Mitutoyo micrometers that I bought new in 1972. I too am considering a switch to digital. I think you might get more replies if you posted this...
  7. Replies
    20
    Views
    1,467

    200-Amp Digital AC/DC TIG & ARC Welder – Eastwood...

    200-Amp Digital AC/DC TIG & ARC Welder – Eastwood Do you have any experience with this Eastwood welder? I do a lot of silicon bronze tig brazing at less than 75 amps and currently using a Lincoln...
  8. Replies
    20
    Views
    1,467

    I have a similar machine (Heliarc 250) that I...

    I have a similar machine (Heliarc 250) that I will be selling. From what I have seen the base machine with torch, working, you can try it out $400 max. I have a Miller coolmate 4 cooler that should...
  9. Replies
    69
    Views
    4,721

    A grill manager at McDonalds?

    A grill manager at McDonalds?
  10. Replies
    76
    Views
    6,008

    Did you ever get this fixed?

    Did you ever get this fixed?
  11. Replies
    25
    Views
    4,836

    I used to have a Miller 350P like that. Welds as...

    I used to have a Miller 350P like that. Welds as good as my XMT304 with 22 wire feeder and runs on single phase.
  12. Replies
    76
    Views
    6,008

    I have been running a single buck-boost...

    I have been running a single buck-boost transformer to L1 for over 15 years. If you are running off your main panel, neutral and ground are bonded. Why don't you contact Phase Perfect to make sure?
  13. Machine a 12" x 18" x 12" piece of stainless on a...

    Machine a 12" x 18" x 12" piece of stainless on a machine that will fit thru a 34" door? Please take a video.
  14. How large and what material are the parts you...

    How large and what material are the parts you want to machine?
  15. Replies
    14
    Views
    1,308

    267307You could try some of this.

    267307You could try some of this.
  16. Replies
    76
    Views
    6,008

    And then the bad part, you have to check out....

    And then the bad part, you have to check out. Radio Shack "what is your phone number" , me "1-800-cash"
  17. Replies
    41
    Views
    4,240

    Gamer video cards are terrible for "shaded with...

    Gamer video cards are terrible for "shaded with edges" which I use all the time. I agree with ecc memory, I just had a stick of ddr4 fail
  18. Replies
    76
    Views
    6,008

    I never thought I would miss Radio Shack but the...

    I never thought I would miss Radio Shack but the convenience was nice. Electronic Supply by Industrial Electronics in Milwaukee Wisconsin : Potter Brumfield, Radio Shack Stores in Milwaukee ...
  19. Replies
    41
    Views
    4,240

    This re-seller has some interesting benchmarks....

    This re-seller has some interesting benchmarks. Recommended Workstations for SOLIDWORKS - Puget Systems
  20. Replies
    76
    Views
    6,008

    Your machine ran without a problem when you first...

    Your machine ran without a problem when you first brought it home? The high voltage most likely over stressed a component which caused your problem. So after you lower your incoming voltage your...
  21. Replies
    76
    Views
    6,008

    Buck and Boost Transformer Calculator - Schneider...

    Buck and Boost Transformer Calculator - Schneider Electric United States This should give you an idea of what you need. Federal Pacific Electrical Transformer SB24N1.5F Pri. 240x480 Sec. 24/48...
  22. Replies
    76
    Views
    6,008

    If you are using a Phase Perfect, use 1 buck...

    If you are using a Phase Perfect, use 1 buck boost transformer on the single phase input of the Phase Perfect. My single phase is usually around 247 volts and that is what i did to lower it.
  23. Replies
    7
    Views
    1,549

    It sounds like new features are going to Fusion ...

    It sounds like new features are going to Fusion
    Why no updates to Inventor Cam? - Autodesk Community
  24. Sticky: I hear Spinit laughing in the background.

    I hear Spinit laughing in the background.
  25. Replies
    88
    Views
    6,048

    Get a Phase Perfect.

    Get a Phase Perfect.
Results 1 to 25 of 1376
Page 1 of 56 1 2 3 4