Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Hodge

Page 1 of 26 1 2 3 4

Search: Search took 0.01 seconds.

  1. Here ya go digger, not exactly please but should...

    Here ya go digger, not exactly please but should do.
    Watch "A Few Good Men (3/8) Movie CLIP - Ask Me Nicely (1992) HD" on YouTube
    YouTube
  2. Replies
    109
    Views
    5,924

    Vitamin L = lead poisoning.... at a high rate of...

    Vitamin L = lead poisoning.... at a high rate of fps.
  3. Replies
    21
    Views
    1,257

    You could put OT(off topic) in your title line....

    You could put OT(off topic) in your title line. This falls within forum guidelines and is considered acceptable. It would not be the first time someone asked a question beyond the confines of...
  4. Replies
    109
    Views
    5,924

    Sounds like a rather costly squirrel trap,...

    Sounds like a rather costly squirrel trap, effective though.
  5. Replies
    109
    Views
    5,924

    Ok, let's see, try this: Watch "Leaf Blower vs...

    Ok, let's see, try this: Watch "Leaf Blower vs Chipmunks and a Squirrel" on YouTube
    YouTube
  6. Replies
    109
    Views
    5,924

    I don't think so, we've got enough already....

    I don't think so, we've got enough already. Unless you are willing to swap squirrels for opossums.
  7. Replies
    18
    Views
    1,587

    Agreed, looks like a tarted up mess by a...

    Agreed, looks like a tarted up mess by a sharpster. Lots of pretty pictures but no definitive shots of high wear areas.
  8. Replies
    37
    Views
    27,291

    Look, two spammers with one old thread, bonus...

    Look, two spammers with one old thread, bonus points for first post apiece
  9. Don't forget a valid driver's license.......

    Don't forget a valid driver's license.......
  10. Chin up now, you may find you are equal to a...

    Chin up now, you may find you are equal to a certain fellow by the name of Hugh Glass
  11. Replies
    906
    Views
    32,140

    Very carefully, you only get one try.....

    Very carefully, you only get one try.....
  12. Replies
    16
    Views
    1,616

    Agreed, though at this point it's advice falling...

    Agreed, though at this point it's advice falling on deaf ears so to speak.
  13. Replies
    67
    Views
    3,964

    Farmers. Com......

    Farmers. Com......
  14. Replies
    16
    Views
    1,616

    Based on what you've told it sounds more like a...

    Based on what you've told it sounds more like a parts machine/ basket case. Unless the majority of the parts are there(90% or more) you'll spend more time and money attempting to put it to rights...
  15. Replies
    67
    Views
    3,964

    All joking aside I have popped the seals off the...

    All joking aside I have popped the seals off the sealed bearing and regreased for longer life
  16. Replies
    67
    Views
    3,964

    And there you have it..... you've blown the...

    And there you have it..... you've blown the bearings....:D
  17. Replies
    30
    Views
    2,538

    Correct me if I'm mistaken, but wouldn't the...

    Correct me if I'm mistaken, but wouldn't the cutter bar interfere in getting a proper measurement?
  18. Replies
    11
    Views
    1,083

    pictures of course.....and welcome to the forum

    pictures of course.....and welcome to the forum
  19. Depends on who is in charge and their definition...

    Depends on who is in charge and their definition of "greater good". Think about that for a bit.
  20. Replies
    5
    Views
    1,097

    While I'm sure this thread will generate some...

    While I'm sure this thread will generate some interest, you might want to check out the selling and participation guidelines.
  21. Replies
    5
    Views
    1,082

    Get in some of the political discussions and...

    Get in some of the political discussions and agitate a bit......
  22. Replies
    50
    Views
    2,431

    Just an observation, not meant to be snarky, I...

    Just an observation, not meant to be snarky, I would think twice before removing/ replacing the existing drive system. It's real easy to lower the performance, much harder to improve on the factory...
  23. Replies
    86
    Views
    4,611

    If all else fails you could introduce a ravenous...

    If all else fails you could introduce a ravenous tribe of thermites to the pallet and they will quickly chew the wood from underneath.....
  24. Replies
    30
    Views
    2,191

    Admittedly I'm biased in favor of a rpc for its...

    Admittedly I'm biased in favor of a rpc for its simplicity and longevity. But $1500 for a 10hp rpc is overpriced quite a bit for someone capable of doing it themselves. I'm thinking $500 tops and...
  25. Replies
    86
    Views
    4,611

    Good call, not nearly as expensive as a damaged...

    Good call, not nearly as expensive as a damaged lathe. It's not a hard job if you have been exposed to this type of work but can be daunting if not.
Results 1 to 25 of 642
Page 1 of 26 1 2 3 4