Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: iwananew10K

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    23
    Views
    2,053

    gonna be down for a bit, but small victories...:)...

    gonna be down for a bit, but small victories...:)

    It's not all buttoned up cause I need to make new shims and set clearances but it's clean and smooth turning , reused the original square wood...
  2. Replies
    10
    Views
    515

    most gun guys seem to like the replaceable brass...

    most gun guys seem to like the replaceable brass tips, otherwise no real advantage I can tell.

    the only personal experience I can give is the tools4cheap steadies were actually quite nice, I used...
  3. Replies
    10
    Views
    515

    lost creek machinery has one of the tools for...

    lost creek machinery has one of the tools for cheap steady rests that is made to accept adapters to fit different machines....it has the @[email protected]$ adapter but you could easily make one for your Sheldon,...
  4. I'm afraid I don't meet your prerequisites.:) ...

    I'm afraid I don't meet your prerequisites.:)

    I will say it's pretty neat looking and would like to see more views.
  5. Replies
    15
    Views
    1,674

    4.5 thou is nothing...get your mechanicals sorted...

    4.5 thou is nothing...get your mechanicals sorted and you'll be fine.

    Have fun with it and think fondly of dad while you use it....he will be watching.:)
  6. whew, for a second I thought you might be this...

    whew, for a second I thought you might be this guy.

    Kerf Loss: Minimizing Loss Per Cut with REALLY expensive material
  7. serial is 39441....what looks like a - is an...

    serial is 39441....what looks like a - is an incomplete stamp from the 4...look at the first 4 to see what I mean.

    cool old SB.
  8. knowing/seeing the design would help w/ regard to...

    knowing/seeing the design would help w/ regard to suggestions.
  9. FWIW- I don't replace filler, don't have...

    FWIW- I don't replace filler, don't have to....today's paints along with some creative techniques make it unneeded...I let the paint get tacky and then "stiple" it with the end of the brush...it will...
  10. Replies
    7
    Views
    1,073

    contrary to what you may have been told, size...

    contrary to what you may have been told, size does matter.:D

    <hint,hint>

    ps- what kind of duty too? Is CI body fine,or do you need steel?
  11. Replies
    5
    Views
    741

    That is standard box for workshop series 9/10k...

    That is standard box for workshop series 9/10k -AFAIK the only one ever offered.
  12. sounds like the filler coat....usually thick on...

    sounds like the filler coat....usually thick on the head and bed....nasty stuff....on the old ones I would swear they used pig dung...stinks like hell.
  13. in my perhaps controversial opinion, provided all...

    in my perhaps controversial opinion, provided all is properly adjusted,there is little you can do to the SB9 to increase "rigidity".....making the SB9 perform is ALL about the cutting tool, there is...
  14. Replies
    7
    Views
    1,398

    IMO if backlash is enough to bother you, the...

    IMO if backlash is enough to bother you, the better solution by far is a new nut and/or screw.....compensating nuts do not fix the problem and actually just make things worse....between backlash and...
  15. Replies
    5
    Views
    497

    Seal-Off Grease Adapter - LOCKNLUBE...

    Seal-Off Grease Adapter - LOCKNLUBE

    thar 'ya go.:)
  16. Replies
    9
    Views
    1,210

    If it's really ready to go and condition is good...

    If it's really ready to go and condition is good then that's not bad...old lathes are expensive and if all you have to do is tool up, you can spend your time making stuff rather than fixing a lathe.
  17. do not use a 4j for holding an end mill...the...

    do not use a 4j for holding an end mill...the chances of it holding straight are practically nil...unless you have a VERY nice 4j....collets are better, but even better is an end mill holder.
  18. Thread: 10k Help!

    by iwananew10K
    Replies
    5
    Views
    734

    South Bend Lathe Model 10K ● Full Rebuild Package...

    South Bend Lathe Model 10K ● Full Rebuild Package ● Manual, Felts, Oil, Grease ! | eBay

    Look over this site for all sorts of info, check the serial database to get your date...make sure you are...
  19. Replies
    23
    Views
    2,053

    '37 serial with a '39 ship date- to Osborn...

    '37 serial with a '39 ship date- to Osborn Manuafacturing in Cleveland.
    263921


    what I'm a little unsure about is the PRI gear 3...what is "3"???
  20. Replies
    10
    Views
    1,194

    shame he sanded off the ridge...that was an...

    shame he sanded off the ridge...that was an indicatable surface to go off.

    feeler gage city. :)

    sacrificial sub plate bolted down to mill table, mill mating slot in-situ for the bases...
  21. Replies
    4
    Views
    458

    http://vintagemachinery.org/pubs/1617/17785.pdf

    http://vintagemachinery.org/pubs/1617/17785.pdf
  22. other than a "pseudo" key way it is an otherwise...

    other than a "pseudo" key way it is an otherwise featureless gear....the stud it goes on has a shoulder to set its axial clearance, and there is a round pin in the stud it goes on that engages the...
  23. heavy 9/10 single tumbler idler gear face width

    27T idler gear that goes on the selector arm...I have 2 samples, one is .275" and the other is .285"

    It's not a critical dimension, but want to be able to give Stephen a good average for his parts...
  24. Replies
    23
    Views
    2,053

    had to see how well my new paint matched up...I...

    had to see how well my new paint matched up...I can now confirm there are at least 51 shades of gray.;)
    263798

    PS- that's just the first 'rough" coat....SW all surface enamel, pretty decent stuff.
  25. Replies
    0
    Views
    428

    FYI- Sherwin Williams 30% off

    stock up if you be needing it.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4