Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Larry Dickman

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. We round up all the psychos, and march them off...

    We round up all the psychos, and march them off to Denmark. :D
  2. you guys have been debating this for 100 pages...

    you guys have been debating this for 100 pages and have yet to come up with a solution. Meanwhile a bunch of kids got shot up this morning. Thanks for nothing
  3. Replies
    8
    Views
    325

    it should be in the ballpark

    it should be in the ballpark
  4. Replies
    4
    Views
    187

    I just use a rubber band

    I just use a rubber band
  5. Replies
    296
    Views
    74,902

    I like his address too, near apt B. Is that where...

    I like his address too, near apt B. Is that where he's parked?
  6. I've always found that SS and HSS should never be...

    I've always found that SS and HSS should never be used in the same sentence.

    I think you'd be sorry using SC without coolant through. We've always relied upon OSG gold cobalt for 304/316
  7. not a surf board? 269934

    not a surf board?
    269934
  8. Replies
    21
    Views
    895

    whatever you buy, I would suggest you permanently...

    whatever you buy, I would suggest you permanently mark them with your companies name. Platers love to steal them and give you your parts back in used beer cases..
  9. Who are you using? Wouldn't a phone call to them...

    Who are you using? Wouldn't a phone call to them clear things up?

    You might try Varco or Bodycoat
  10. here's a link from a few years back Form...

    here's a link from a few years back

    Form tapping a no-no in aerospace?
  11. I had to tap a bunch of M2's in 304 a while back....

    I had to tap a bunch of M2's in 304 a while back. Someone suggested form taps and I thought, no way, this stuff is way too hard. I ran the whole job with one drill and one tap.

    That size of tap,...
  12. roll taps work awesome on 316, and they never...

    roll taps work awesome on 316, and they never break
  13. Replies
    263
    Views
    15,495

    Great. Now we'll have to contend with a big hole...

    Great. Now we'll have to contend with a big hole in the ozone layer from all the goat farts.
  14. Replies
    32
    Views
    1,826

    Ya, use a good quality coolant. (No, not Blaser)...

    Ya, use a good quality coolant. (No, not Blaser) Problem goes away
  15. how were they able to find a rainy day in so cal?

    how were they able to find a rainy day in so cal?
  16. how deep? And I assume you mean the ID of the...

    how deep? And I assume you mean the ID of the bore, and not the face. An old trick to roughen up the surface finish of lee plug holes is to very lightly run a thread mill around it.
  17. Replies
    52
    Views
    2,013

    Doing it algebraically, all you need to do it...

    Doing it algebraically, all you need to do it adjust your offset values to compensate for the tool radius.
  18. Replies
    52
    Views
    2,013

    Ok, so We've got our angled line as Y=-1.3691 X +...

    Ok, so We've got our angled line as Y=-1.3691 X + 4.5892 and now we know our arc center

    So the equation for any point on the circumference is R^2 = (Xc-X1)^2 + (Yc-Y1)^2 where XcYc is the center...
  19. Replies
    52
    Views
    2,013

    Ok, so as mentioned above, your length dimensions...

    Ok, so as mentioned above, your length dimensions are to the theoretical intersections, not the arc centers. Lets take as an example, the end of the .375 radius at the angle.

    Step one is to find...
  20. Replies
    52
    Views
    2,013

    shut up and listen, and you might learn something

    shut up and listen, and you might learn something
  21. Replies
    52
    Views
    2,013

    im in the middle of an as9102, as soon as im done...

    im in the middle of an as9102, as soon as im done I should have a minute to show you how to calculate it. BTW, trig has no place in this.
  22. Replies
    52
    Views
    2,013

    how's your math? It's simple algebra. Define...

    how's your math? It's simple algebra.

    Define the radius as R^2=X^2 + Y^2 and the lines as Y=mX + b, then just solve for the intersections.
  23. Sounds like you need to shim the table up .006" ...

    Sounds like you need to shim the table up .006"

    Or maybe, what tool setting routine are you using, the straight down one or the one where it rotates ccw? With a 1/2" cutter, you're right on the...
  24. Replies
    263
    Views
    15,495

    he shoved them up his ass?

    he shoved them up his ass?
  25. like you say, there are a lot of variables, but I...

    like you say, there are a lot of variables, but I would say 512k isn't even going to get you started. Most of our surfacing paths end up in the 1-12meg range.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4