Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Danny1788

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    1,817

    Dang that sounds sweet wish I knew how to run CNC...

    Dang that sounds sweet wish I knew how to run CNC equipment. That's exactly what I would do with that little mill.
  2. Replies
    16
    Views
    2,216

    Show picture of your progress, should be a cool...

    Show picture of your progress, should be a cool project. I always like seeing your projects, you do a very good job of explaining them.
  3. Replies
    7
    Views
    2,111

    Cerakote makes and air dry product that does not...

    Cerakote makes and air dry product that does not need to be baked on. It works well on stocks and other things that cannot be heated as much.
  4. Replies
    16
    Views
    2,859

    Its 1/8" NPT which is closer to 5/16" and yes I...

    Its 1/8" NPT which is closer to 5/16" and yes I drill with a Q drill bit .332" so this works for anything under 8mm if you do a 338 rifle barrel just drill and tap for 1/4" NPT threads.
  5. Replies
    16
    Views
    2,859

    If your a cheap A$$ like I am, maybe try this.......

    If your a cheap A$$ like I am, maybe try this....

    I setup my barrel in the lathe and center the muzzle super quick only to .001" then I drill and tap it 1/8"NPT with a short bottoming tap. Take...
  6. Dude, that's awesome well thought out and well...

    Dude, that's awesome well thought out and well executed!!!! hands down one of the coolest things ive seen on here in awhile.
  7. Thread: Cerakoting

    by Danny1788
    Replies
    29
    Views
    6,904

    What pressure do you spray at?

    What pressure do you spray at?
  8. Replies
    3
    Views
    1,103

    Remington M-700 Sear Spring...

    Remington M-700 Sear Spring
  9. Replies
    3
    Views
    1,103

    First of all, Why on gods green earth would you...

    First of all, Why on gods green earth would you want an Xmark trigger over the older blued walker trigger that you are talking about? the Xmarks are JUNK, they can be adjusted but are cheaply made....
  10. Replies
    35
    Views
    7,614

    If you want to use a smaller lathe, then chamber...

    If you want to use a smaller lathe, then chamber through the head stock with a 4jaw and an outboard spider. Make sure to get a lathe with a large enough spindle bore. Also put Copper wire around the...
  11. Here is my flush setup. I used a cheap harbor...

    Here is my flush setup. I used a cheap harbor freight pump, it puts out about 45psi with the heavy sulfur cutting oil I use and moves chips out very well. I still cut pretty slow at about .050" then...
  12. Replies
    13
    Views
    5,136

    This was my problem. By adding the long stem to...

    This was my problem. By adding the long stem to my indicator it changed the value more than I thought. I put the short contact point back on and checked the breech side and it was .0005 out

    I then...
  13. Replies
    13
    Views
    5,136

    The barrel is brand new, no chamber cut yet. Im...

    The barrel is brand new, no chamber cut yet. Im dialing it in to chamber it. I know all barrels have some curve to them I'm not sure how much as ive only chambered 4 barrels so far and non of them...
  14. Replies
    13
    Views
    5,136

    I haven't done the math myself but I read a post...

    I haven't done the math myself but I read a post awhile back I think its around .0003" when you add the long tip. But its not even moving on the indicator.

    I'm mainly looking for someone with...
  15. Replies
    13
    Views
    5,136

    Indicating a barrel for chambering?

    So I'm about to chamber up a new 7mm brux barrel and I'm a little stumped. Normally I just use a range rod with the proper fit bushing and dial in the barrel on the chamber/breech end with my...
  16. Replies
    20
    Views
    10,155

    here is the one I built its made out of 3.00"...

    here is the one I built its made out of
    3.00" OD x .500 wall x 2.00" ID 1020 DOM Round Steel Tube

    I used 3/8x24tpi brass tipped screws from McmasterCarr.com 1" long with no heads. I would use...
  17. Replies
    4
    Views
    2,842

    Grizzly g9729 upgrades

    Anyone that owns a Grizzly G9729 what upgrades have you done so far? has anyone done any modifications to the lathe to slow it down for easier threading? Could it be doen with simply changing the...
  18. Replies
    10
    Views
    1,703

    Thanks guys will seriously be reading up before...

    Thanks guys will seriously be reading up before starting to thread. keydiverfla I will take you up on that offer then I start to setup my lathe thank you.
  19. Replies
    18
    Views
    5,323

    I use an RCBS chargemaster combo and it has...

    I use an RCBS chargemaster combo and it has always given me good loads. Is it the most accurate as far as variances of 0.001 grs NO but it will do tenths and is very repeatable which is the main...
  20. Replies
    10
    Views
    1,703

    Thanks guys do you know of any good gunsmithing...

    Thanks guys do you know of any good gunsmithing books to purchase?
  21. Replies
    10
    Views
    1,703

    Newbie need help

    I am new to turning on a lathe, I have used an endmill before but very basic stuff nothing fancy. I would like to ask this in the gunsmithing section as I purchased a lathe to start making my own...
  22. Replies
    21
    Views
    25,002

    Tag me in I would be interested if this ever...

    Tag me in I would be interested if this ever happens
Results 1 to 22 of 22