Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Street

Page 1 of 34 1 2 3 4

Search: Search took 0.01 seconds.

  1. you must know your way around Cnc's or you do...

    you must know your way around Cnc's or you do now...

    thanks for the vid
  2. Thread: UK Gun Auction

    by Street
    Replies
    3
    Views
    393

    limy thats a very sad listing...

    limy thats a very sad listing...
  3. Replies
    20
    Views
    985

    there was a Nazel that came up for sale see...

    there was a Nazel that came up for sale see attached.
    It was quite a while ago here are the pictures, any big hammer seems to be rare.

    302743302744302745302746
  4. Replies
    14
    Views
    614

    Pull the motor rotor and turn down to a...

    Pull the motor rotor and turn down to a consistent size....bore and bush the pulley down to the motor shaft size.
    Obviously scotch key the bush ( bush being a press fit to pulley) to the pulley and...
  5. Replies
    815
    Views
    25,733

    302725i am just wondering how accurate the...

    302725i am just wondering how accurate the information is ...the data being put forward by CBS
    here
    2020 Election Battleground Tracker: Polls from all 50 states
  6. Replies
    32
    Views
    1,546

    try this metabo battery powered tapper, and yes a...

    try this metabo battery powered tapper, and yes a guide to get it perpendicular would be good.

    GB 18 LTX BL Q I (603828890) Cordless Tappers | Metabo Power Tools
  7. Replies
    18
    Views
    1,087

    Just looking at it...the first thread may be ok...

    Just looking at it...the first thread may be ok but the rest won't be engaged in the right way so load initially will be on the "first thread" then transfer to the others and to do this it will have...
  8. Cat sets over here in that size are rebadged...

    Cat sets over here in that size are rebadged perkins powered sets ( cat badge engineering ) they are just Olympian sets out of the UK.

    Maybe different in the USA but not likely so don't pay a CAT...
  9. Replies
    74
    Views
    3,626

    I have some proto, Caterpillar and others Knipex...

    I have some proto, Caterpillar and others Knipex make nice pliers they are german.

    Cat has tools of comparable quality to snap on and if you work there you get staff discount, snap on man is not...
  10. just use a venturi metering system. We just turn...

    just use a venturi metering system.
    We just turn the water tap on and it draws concentrated coolant into the water stream at a set rate.
    Its as easy as turning on the tap.
  11. There is also tekla, there is a trial version but...

    There is also tekla, there is a trial version but do not know the limitations on it, if it just prints it with a disclaimer or does not do certain parts of analysis or maybe doesn't save the file.
    ...
  12. oh that picture of the shack does not look...

    oh that picture of the shack does not look cyclone proof at all.......
  13. Well Autocad is the go to for Architects here,...

    Well Autocad is the go to for Architects here, some use Rhino for Curved surfaces and 3d modeling.this is where auto cad falls down.They are hard to build in Advanced places so stay away from...
  14. Replies
    75
    Views
    3,021

    A Genset still will suck when it comes to rebuild...

    A Genset still will suck when it comes to rebuild and or if it does irreparable damage to itself like drop a valve and keep running on the other cylinders till it finally stops..
    Even if you make it...
  15. Replies
    75
    Views
    3,021

    since you note the cost is about the same for...

    since you note the cost is about the same for power company to Genset...go with the power company as you don't have to rebuild the genset when it logs it final hour...

    If your in a sunny area what...
  16. Thread: Death of a pet

    by Street
    Replies
    149
    Views
    6,543

    Why wait to if he survives to Thursday?..the dog...

    Why wait to if he survives to Thursday?..the dog could be suffering now, so do it soon would be best.
  17. Replies
    43
    Views
    2,708

    i think you will find there is not much time in...

    i think you will find there is not much time in Reconditioning a engine and setup speed counts for allot, the old way of grinding seats takes time the new way of cutting seats and vacuum testing is...
  18. Replies
    11
    Views
    724

    All the induction heaters i have used with a...

    All the induction heaters i have used with a sensor to detect temp we never went over 120 degrees Centigrade for fitting.....it worked fine.
  19. Replies
    2
    Views
    513

    never heard of a pocket book... you can get...

    never heard of a pocket book...

    you can get the manuals from Okuma in pdf form, which is the cheapest way to get them. buying as a set is best.

    I have the osp2001 set
  20. Replies
    41
    Views
    20,054

    Lard was used at the shop i did my time at, for...

    Lard was used at the shop i did my time at, for all pressed in bushes etc it worked
  21. Yes you've answered if its 4 inch if thats what...

    Yes you've answered if its 4 inch if thats what he's doing is too thin to fit it with cover allowance.

    Not sure how deep he's going on the slab and just how big a area he is doing, just says a...
  22. [/COLOR] Well you need to have a look at that...

    [/COLOR]

    Well you need to have a look at that sentence again as its not correct on bending moments in for suspended slabs or slabs on ground ( this case )
    That if you need two layers of steel,...
  23. Replies
    4
    Views
    1,219

    the listing should be with multiple photos of...

    the listing should be with multiple photos of each machine and try to keep the tooling with each if you know where it goes.
    Some tooling can be costly.
    Clear photos are a good start...then you have...
  24. I like a nice bright white light, i found the...

    I like a nice bright white light, i found the leds i could buy where a yellow light, no matter what the box said on it.. it was always a yellow light much like the old incadesent bulbs.

    I use...
  25. Replies
    18
    Views
    1,166

    i tend to like the white metal method as i have...

    i tend to like the white metal method as i have done a few whitemetal bearings before.
    Your going to need to soot the shaft fairly heavily, i think it will be trickier with a thread, especially the...
Results 1 to 25 of 838
Page 1 of 34 1 2 3 4