Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: zschary

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    17
    Views
    1,268

    so go to .05 depth, then feed down towards me...

    so go to .05 depth, then feed down towards me across part toward center right? and take .05 pass across the part? Interesting.. it does need a square non radius to the bottom, i am guessing...
  2. Replies
    17
    Views
    1,268

    Litlerob1 suggested the HFHL holder which is what...

    Litlerob1 suggested the HFHL holder which is what my ISCAR rep is saying on this.. Iscar is calling for a ic808 grade.. I would like to do this on the lathe if poss, not have to transfer to the...
  3. Replies
    17
    Views
    1,268

    1018 steel face grooving tips and speeds etc

    have to hog out steel with a face grooving tool capable of 1.2 inch depth .. The lathe is 25 hp and the groove is around 5 inch to 3 inch from center on a 6.5 inch part diameter..

    I do machine...
  4. Replies
    10
    Views
    976

    Philabuster, thank you for the info.. I did find...

    Philabuster, thank you for the info.. I did find a 45 kva dry type transformer that will work.. The question i have is whether i need a disconnect in between the feed breaker going to the primary...
  5. Replies
    10
    Views
    976

    No i am doing all three.. thanks for that tip.....

    No i am doing all three.. thanks for that tip..
    i have been looking on ebay.. will have to figure this out..

    thank you to all who helped on this.. Zach
  6. Replies
    10
    Views
    976

    Transformer woes....

    hey guys, moved to a new shop that has 240v 3phase not 208 .. changed some of the legs on the transformer in my 2005 romi e320 (fanuc control), to accept the new voltage per Romi. It ran fine...
  7. Replies
    7
    Views
    748

    ok.. got it.. .the reference is in misc.. number...

    ok.. got it.. .the reference is in misc.. number 4 like mentioned above thank you !!
  8. Replies
    7
    Views
    748

    :smoking: ok ok.. i better get my ass over...

    :smoking: ok ok.. i better get my ass over there, being hit on many fronts, weekends are for sissy's anyway... :)
  9. Replies
    7
    Views
    748

    ok great... thanks for the tips.. will try on...

    ok great... thanks for the tips.. will try on monday....
    Zach
  10. Replies
    7
    Views
    748

    LNS bar feed home position

    Fast question.. sorry if its been asked before..

    The LNS team told me once how to reset the 0 home position of the carrier when it gets lost.. Can anyone here tell me how to do that.. says .216...
  11. Replies
    3
    Views
    695

    Fanuc Subspindle positioning questions

    Finally getting to the sub spindle on a Romi E320 with a fanuc 18i control. I noticed that the subspindle positioning is a negative number when activating the part transfer codes, I imagine that is...
  12. Ok... GOT IT.. I changed some parameters but i...

    Ok... GOT IT.. I changed some parameters but i believe what the prob was the addl chuck close signal before the romi m21 (which includes that signal) So, it is now working and running while we...
  13. Yea.. this one does not see the chuck open and...

    Yea.. this one does not see the chuck open and close signals.. It says this on the interface paper for my machine..
    load/chuck open= M20
    Chuck close/dwell = M21
    end of bar = m80

    doing good on...
  14. LNS bar feed Fanuc 18I quick (i hope) question

    so here is the code i have been using at the end of program to run the barfeed
    all works .. It is a servo 65 short bar type. The thing is the M21.. I spoke to Fred at LNS and the typical chuck...
  15. I will look tomorrow thanks Ox.. The machine has...

    I will look tomorrow thanks Ox.. The machine has an EXT side of the work offset page .. the Romi folks have had me put some stuff in there.. I dont believe it was a belt or other.. When i got the...
  16. Romi drill on center and general axis setup questions ROMI BMSY

    Were just about ready now to run this machine, figured the bugs etc.. On programs that i load the machine hits the hard stop at the top of the x axis like it does not know where it is.. It is a...
  17. Replies
    11
    Views
    1,304

    the feeder has run with the lathe.. The control...

    the feeder has run with the lathe.. The control has freed up and I can now get into the menu.. I think it was that the chuck was closed.. Makes sense that would be the case to feed, but to even...
  18. Replies
    11
    Views
    1,304

    ok.. good to know. I will look for those things.....

    ok.. good to know. I will look for those things.. Is the diagnostic page in the barfeed pendant? i cant get it to go anywhere but the alarm page when it starts up
  19. Replies
    12
    Views
    1,309

    oh man. Seems like there are a few of us...

    oh man. Seems like there are a few of us looking for an answer..
    thank you
  20. Replies
    12
    Views
    1,309

    the end of he switch there is missing the top...

    the end of he switch there is missing the top piece I think that allows that part to go in.. How could I find it in the ladder?
  21. Replies
    11
    Views
    1,304

    I will try to see if the lathe is in estop or...

    I will try to see if the lathe is in estop or other.. THe message and alarm is on the pendant for the LNS not the lathe, but I will see if I had something in estop or other on the lathe.. I will...
  22. Replies
    11
    Views
    1,304

    ok.. thats what i will do.. The feed has an...

    ok.. thats what i will do.. The feed has an option to do that and i will get that going, thanks ox.. if i can get the thing up and running that is..
  23. Replies
    12
    Views
    1,309

    Was thinking that, but i think it needs to see...

    Was thinking that, but i think it needs to see that the door then opens too, not sure, someone said that about it.. Did that work for you?
  24. Replies
    11
    Views
    1,304

    SO we have been setting it up to run, really have...

    SO we have been setting it up to run, really have not turned it on yet and am getting a "line open Possible causes: Connection, Problem in circuitry" Is there a circuit breaker, or someting in...
  25. Replies
    11
    Views
    1,304

    Bar Feeder question

    have a LNS quick load servo 65 i am trying to use..
    the manual says i can use it without the turret stop, my question really is why do you guys use the turret to stop the bars, is it more of a...
Results 1 to 25 of 161
Page 1 of 7 1 2 3 4