Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: chad883

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    541

    I have never needed to cylindrical mill, so I...

    I have never needed to cylindrical mill, so I have not figured out how to do it.

    I do not like T-32 mode. That is why I program the parameter change only during the ops I need it, so no I do not...
  2. Replies
    10
    Views
    541

    Yes, they Y moves are translated into C moves.

    Yes, they Y moves are translated into C moves.
  3. Replies
    10
    Views
    541

    The actual moves are made just like it would be...

    The actual moves are made just like it would be programmed for a mill.
  4. Replies
    10
    Views
    541

    T0303 (1/2 BLIZZARD FACE CEM) G0 G40 G98 M8...

    T0303 (1/2 BLIZZARD FACE CEM)
    G0 G40 G98 M8
    M200
    G97 S2000 M203

    (T-32 MODE)
    G10L50(ENABLE PARAMETER WRITE)
    N1016R240(CHANGES PARAMETER TO MAKE MACHINE T-32 MODE)
    G11(TURN OFF PARAMETER WRITE)
  5. Replies
    10
    Views
    541

    You need 2 options turned on to do this. 19 Polar...

    You need 2 options turned on to do this. 19 Polar coordinate input and 20 cylinderical interpolation, or something like that. Those will allow you to G12.1 and program X and C. If you do not have...
  6. Try R54 bit 5 set to 1. Should make the chuck...

    Try R54 bit 5 set to 1. Should make the chuck stay where it is. ie if clamped ti stays clamped, if unclamped it stays unclamped. These parameters are listed in the electrical diagram. I have seen...
  7. Replies
    9
    Views
    1,058

    I can't say what a 20 HP Haas will do, but a 20...

    I can't say what a 20 HP Haas will do, but a 20 HP Mazak will remove 11 pounds of 1018 in about 2 minutes, and it sounds like a hail storm. That is turning a 4" diameter slug not a bar though.
  8. Replies
    0
    Views
    392

    1993 Mazak H500/40N

    We have a 1993 Mazatech H500/40N for sale. Machine has a E-Stop that we are not able to find and don't want to pay for repair. We upgraded to a newer Mazak horizontal. This machine is available as a...
  9. Mazak lathes will call the last known offset for...

    Mazak lathes will call the last known offset for that tool, if that tool has not been called yet it will default to the primary offset. Call T0101 will bring up tool 1 offset 1. Call T0101.2 it will...
  10. Replies
    18
    Views
    958

    Make sure you have your radius set correctly in...

    Make sure you have your radius set correctly in tool offset. Half the end mill diameter.
  11. Replies
    10
    Views
    840

    I thought end mills are always set to "0"...

    I thought end mills are always set to "0" setting. I always have them set for that, but do not program in degrees. I use polar milling.
  12. If you are storing the program in the machine...

    If you are storing the program in the machine memory, 1 device moved from machine to machine. The ones in the link are for that purpose, they have ones that stay at the machine also. I think that is...
  13. Easiest thing I have ever used. DNC,...

    Easiest thing I have ever used.

    DNC, xlTRANSFER

    or

    Portable USB Connect from Shop Floor Automations

    I have used the first one on my 1995 Fanuc controlled Mori, and it is fine. I have used...
  14. Replies
    26
    Views
    3,033

    The biggest concern would be what control voltage...

    The biggest concern would be what control voltage your control needs. A lot of CNC machines need 24V DC. If your supply power is too high or too low, it will either burn up your boards/drives, or not...
  15. Replies
    1
    Views
    495

    Sounds like your hard drive went out. Timing...

    Sounds like your hard drive went out. Timing would be about right on a 2005.
  16. Replies
    9
    Views
    515

    Probably a dumb question, but did those sub...

    Probably a dumb question, but did those sub programs actuallymake it to the machine? Could it have timed out before finishing?
  17. Replies
    6
    Views
    1,185

    I got the file downloaded. Looking at the...

    I got the file downloaded. Looking at the drawing, I need to get in from the tail stock end, loosen 10 bolts to pop the drive loose. Then get the motor to orient and get my drive lug set correcty....
  18. Replies
    6
    Views
    1,185

    P.M. sent with my email Thanks

    P.M. sent with my email

    Thanks
  19. Replies
    6
    Views
    1,185

    Mori SL25Y live tool drive

    I have a Mori SL 25Y, while drilling a cross hole with a live tool the coolant ran dry. This stopped the drill and alarmed the machine. I got everything reset and homed out. The problem is that the...
  20. Replies
    6
    Views
    659

    I have only ran these on a CNC. 1. Yes 4TPI...

    I have only ran these on a CNC.
    1. Yes 4TPI would be the correct pitch for a 4 start 16 TPI

    2. Not sure on this one.

    3.On CNC I ran one thread complete, then started again at different Z start...
  21. Replies
    12
    Views
    1,423

    I run a 4" face mill 8000 RPM in aluminum, I...

    I run a 4" face mill 8000 RPM in aluminum, I can't say that the TSC is hitting the inserts, but I can say that flood is not. The wind generated from the face mill makes an air curtain that prevents...
  22. Replies
    11
    Views
    1,208

    Did this machine have a bar feeder hooked up? If...

    Did this machine have a bar feeder hooked up? If so it may be seeing the bar feeder e-stop circuit and throwing other alarms from that.
  23. Replies
    0
    Views
    1,109

    Opinions on 1998 MC-V4020

    I am considering expanding my mill capacity with one of these. Please let me know the good, the bad, and the ugly. Also a ballpark value.

    Thanks
  24. Replies
    6
    Views
    876

    Probably the air line going into the tool eye...

    Probably the air line going into the tool eye that blows on the eye when you are touching off tools. Just a guess though.
  25. I usually sync them with 1 of the chuck open so...

    I usually sync them with 1 of the chuck open so they don't fight. May not be necessary.
Results 1 to 25 of 159
Page 1 of 7 1 2 3 4