Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: bob

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    647

    PM sent thanks

    PM sent thanks
  2. Replies
    5
    Views
    663

    Form a blank 3/8 wide

    Form a blank 3/8 wide
  3. Replies
    5
    Views
    663

    Designing punch and die

    I want to build a die to form the dish in attached picture. Material will be .05 brass .375 wide. If I cut them on the edm clearance will be about .0175 per side. Pretty sure that is not nearly...
  4. Replies
    3
    Views
    647

    Picture of scrapers

    Picture of scrapers
  5. Replies
    3
    Views
    647

    FS Bearing Scrapers

    Set of 3 marked Miller's Falls 740 never used $30.
    Bob. Picture coming
  6. Replies
    2
    Views
    649

    Came close to calling the scrapper today

    I have an old Elox/Fanuc wire. Don't use it much but doesn't owe me anything. So on Friday started a long cut it was sparking along all day ok till about 1/2 done when it broke the wire. It was late...
  7. Replies
    2
    Views
    924

    PM sent re PayPal Bob

    PM sent re PayPal
    Bob
  8. Replies
    9
    Views
    1,618

    I checked the 4x4 it's scrap not worth shipping....

    I checked the 4x4 it's scrap not worth shipping. Sorry
    Bob
  9. Replies
    9
    Views
    1,618

    Will check

    Will check
  10. Replies
    0
    Views
    290

    FS Sandvik BTS Tooling

    Three holders and one shank (shop made)$25 for the lot
    Bob
  11. I have 3J collets and chuck would prefer to sell...

    I have 3J collets and chuck would prefer to sell all together but there may be some duplicates that could go.
    Bob
  12. Replies
    13
    Views
    1,063

    Cut .005 off armature runs fine now. Thanks to...

    Cut .005 off armature runs fine now. Thanks to those that offered "Practical" ideas
    Bob
  13. Replies
    2
    Views
    545

    It's a Boehmer motor card is marked Seco 28651J....

    It's a Boehmer motor card is marked Seco 28651J. If you could send your phone number would like to call.
    Thanks
    Bob
  14. Replies
    2
    Views
    545

    BPT power feed not working

    Series II special factory pf. Any body fixed one. I have no manual don't even know if it's supposed to be 110 or 220. Any help or info appreciated.
    Thanks
    Bob
  15. Replies
    13
    Views
    1,063

    Thanks Mark pretty sure that's the problem. Going...

    Thanks Mark pretty sure that's the problem. Going to try Ron's solution nothing much to loose.
    Bob
  16. Replies
    9
    Views
    1,618

    John got it,sorry Bob

    John got it,sorry
    Bob
  17. Replies
    13
    Views
    1,063

    Motor overheat question

    I have a 230 v 2 speed 3 phase motor that runs but gets really hot really fast. I pulled it apart and it appears armature is rubbing, see pictures. Would this be the cause of overheat?

    Thanks
    Bob
  18. Replies
    16
    Views
    851

    This is a pita job depending on tolerance...

    This is a pita job depending on tolerance required etc. I do it fairly often on much smaller parts. Turn the outside to size, bore inside slightly undersize split and cut to length with wire edm....
  19. Replies
    2
    Views
    924

    FS Acme Thread Gage

    Very nice gage. Do not remember where I got it or how much it was but anyway the "probably should not sell it price is $35 shipped.
    Bob
  20. Replies
    0
    Views
    215

    WTB 240 to 600 V transformer

    Three phase 10kva would be enough bigger would work but shipping gets pricey. Maybe could even make a singe phase work if such exists.
    Bob
  21. You might look at Tormach.they have made some...

    You might look at Tormach.they have made some changes since we got ours. They get relatively pricey all tricked out.
    Bob
  22. Replies
    9
    Views
    1,618

    FS Drill chuck arbors

    Went looking for an arbor I needed never found it but figured time to get rid of these. See pics for what I have and pricing.
    Bob
  23. Thread: WTB 18N Jacobs

    by bob
    Replies
    2
    Views
    568

    MT4xJT3 18 goes to 5/8

    MT4xJT3 18 goes to 5/8
  24. Thread: WTB 18N Jacobs

    by bob
    Replies
    2
    Views
    568

    WTB 18N Jacobs

    Prefer Jacobs but any brand same size would be OK. Don't need pretty with or without shank. Ship post office to Canada. Post what you have and need for it.
    Thanks
    Bob
  25. Replies
    4
    Views
    977

    Sorry, should have checked before posting. That...

    Sorry, should have checked before posting. That machine is a lot heavier than it looks in picture.
    Bob
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4