Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: EmanuelGoldstein

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    13
    Views
    650

    Well, that and the non-standard use of G92 would...

    Well, that and the non-standard use of G92 would turn me off, yes. As a veteran of the browser wars, I hate to see standards tromped on.


    That's because you don't have any real controls left,...
  2. Replies
    254
    Views
    30,254

    Speaking of Fords, a new four-door electric...

    Speaking of Fords, a new four-door electric almost ran over me at lunch. Didn't get the model cuz I was busy scurrying but it was white.

    Is Ford selling fullsize electrics in the US now ? Looked...
  3. Replies
    13
    Views
    650

    That's nasty ! Nice explanation, thank you....

    That's nasty !

    Nice explanation, thank you. Made me glad I don't own one :)
  4. Apparently they are ... London Metal Exchange:...

    Apparently they are ...

    London Metal Exchange: LME Steel Scrap

    No idea how big the effect is but .... ?
  5. Replies
    28
    Views
    1,328

    Flat belts and plain bearings are better for...

    Flat belts and plain bearings are better for precision - look at a Crystal Lake some time. They just don't transmit as much power, so the South Bend is not big on hogging. But it's nice to run, for a...
  6. I wonder if this wasn't maybe an anomoly, maybe...

    I wonder if this wasn't maybe an anomoly, maybe caused by people playing in the commodities market or some other mass hysteria ? Tulips once brought big money, too.

    I've never got doodly for...
  7. CellCon maybe ?

    CellCon maybe ?
  8. I would toss it. The blades are not very...

    I would toss it. The blades are not very expensive, even if you did fid a box or two of 1980 inserts, you'd just have the same problem again next time. Get a new holder and move on with life, in this...
  9. Replies
    28
    Views
    1,328

    Pacemakers or the old clunkers ? I would not buy...

    Pacemakers or the old clunkers ? I would not buy American or a Monarch that's older than about 1942. 50's is better.

    They are just too slow and clunky. Even 1,000 rpm and the small thru-hole of...
  10. Replies
    39
    Views
    1,233

    In other words, you've never run silicon carbide...

    In other words, you've never run silicon carbide in a bead blaster so you have no idea what you're talking about. As usual.
  11. Your wish is my command ... 275943 Oops,...

    Your wish is my command ...

    275943

    Oops, those aren't daffodils ... what's that little white flower called ?


    Sigh. Another hard night's work in the reanimatorium ahead, then :(
    ...
  12. Replies
    39
    Views
    1,233

    Cute. But no relevance to reality. You've...

    Cute. But no relevance to reality. You've obviously never done this. WITH a ground lead alligator clamped to the part you're blasting, WITH the blaster heavily grounded, WITH clean fresh beads, WITH...
  13. Replies
    39
    Views
    1,233

    Try blasting with silicon carbide beads. It'll...

    Try blasting with silicon carbide beads. It'll zap your teeth out, even through those heavy rubber gloves.

    But it sounds like his ground fault thingy trips even before he turns on the blaster, so...
  14. Maybe toss up a photo of the part ? I don't think...

    Maybe toss up a photo of the part ? I don't think anyone is going to graze through all those points to see what you're talking about.

    If it's a swoopy shape, search "import point cloud" for some...
  15. Bridgeport ? Milland, shame shame ! You wrote...

    Bridgeport ? Milland, shame shame ! You wrote '.005" wire' in that same sentence as Bridgeport ! That's the worst advice I've ever seen from you !

    One of those little Electro-Mechano high speed...
  16. Replies
    17
    Views
    769

    Yes, first step, take the tubes out and run them...

    Yes, first step, take the tubes out and run them down to your neighborhood Thrifty drugstore and check them on the tester :)
  17. Replies
    13
    Views
    650

    Boy am I glad I never had one of these...

    Boy am I glad I never had one of these easy-to-use controls.

    G92 is killer.
  18. Cleveland and I think Lees-Bradner built...

    Cleveland and I think Lees-Bradner built eight-spindle hobbers. But what they did was, they put eight individual machines on a huge merry-go-round with one operator station. That's kinda like putting...
  19. What can you do if they aren't ? :cryin:

    What can you do if they aren't ? :cryin:
  20. It would be better than a tinkertoy if he wanted...

    It would be better than a tinkertoy if he wanted to do a Linux CNC project. And had about ten years to make it run :)
  21. You're right, I got it twisted a bit when I found...

    You're right, I got it twisted a bit when I found out much of what they were selling is made in Asia. They do not advertise that fact. The whole enteprise now seems very Harvard MBA, peddle the "Made...
  22. For two people that agree, we sure managed to...

    For two people that agree, we sure managed to turn this into an argument :)

    I do agree with you that hardware is much better. I just don't think that commercial software has improved for the last...
  23. I thought they were great, thank you. Did you...

    I thought they were great, thank you.

    Did you notice how the advertising has changed ? Surface speeds, materials, depth of cut, feedrate ? In an ad for a machine tool ? Whoa, what will they think...
  24. Replies
    14
    Views
    1,839

    We know what actually happened now, but I'd like...

    We know what actually happened now, but I'd like to correct you on dates a little.

    San Francisco was fine until the late seventies - some time between 1978 and 1980, I'd say. I worked there in...
  25. Space cutter and a dividing head is good enough...

    Space cutter and a dividing head is good enough for these, actually.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4