Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: chad883

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    34
    Views
    2,201

    Most of your list will have to be done on a 2...

    Most of your list will have to be done on a 2 axis lathe set up also, so is it just this lathe that takes longer?
  2. Replies
    8
    Views
    711

    Can't help there, mine actually came with all the...

    Can't help there, mine actually came with all the manuals.
  3. Replies
    20
    Views
    1,281

    External P.D. 1.0506-1.0665 Internal P.D. ...

    External P.D. 1.0506-1.0665
    Internal P.D. 1.0750-1.0909
  4. Why not keep the job and sub it out to your...

    Why not keep the job and sub it out to your friend. Keep 10% for yourself and give him the fixtures
  5. Replies
    8
    Views
    711

    I have one of these and really like it. It has...

    I have one of these and really like it. It has the Y axis completely independant. A lot of Y axis lathes use a wedge design and make a move in X that you do not really see, this one does not. In a...
  6. Replies
    20
    Views
    1,281

    I just put it into my thread software....

    I just put it into my thread software.
    1-1/16"-10 2G acme thread

    External P.D 1.0125-1.0285
    Internal P.D. .9888-1.0045
  7. Replies
    9
    Views
    739

    I am not sure if the SQT will support it, but I...

    I am not sure if the SQT will support it, but I use G68.5 plane rotate on the Integrex. I have not tried on any of our SQT's because I do not have a holder that angles. One will run a canned drill...
  8. Replies
    10
    Views
    852

    I have never needed to cylindrical mill, so I...

    I have never needed to cylindrical mill, so I have not figured out how to do it.

    I do not like T-32 mode. That is why I program the parameter change only during the ops I need it, so no I do not...
  9. Replies
    10
    Views
    852

    Yes, they Y moves are translated into C moves.

    Yes, they Y moves are translated into C moves.
  10. Replies
    10
    Views
    852

    The actual moves are made just like it would be...

    The actual moves are made just like it would be programmed for a mill.
  11. Replies
    10
    Views
    852

    T0303 (1/2 BLIZZARD FACE CEM) G0 G40 G98 M8...

    T0303 (1/2 BLIZZARD FACE CEM)
    G0 G40 G98 M8
    M200
    G97 S2000 M203

    (T-32 MODE)
    G10L50(ENABLE PARAMETER WRITE)
    N1016R240(CHANGES PARAMETER TO MAKE MACHINE T-32 MODE)
    G11(TURN OFF PARAMETER WRITE)
  12. Replies
    10
    Views
    852

    You need 2 options turned on to do this. 19 Polar...

    You need 2 options turned on to do this. 19 Polar coordinate input and 20 cylinderical interpolation, or something like that. Those will allow you to G12.1 and program X and C. If you do not have...
  13. Try R54 bit 5 set to 1. Should make the chuck...

    Try R54 bit 5 set to 1. Should make the chuck stay where it is. ie if clamped ti stays clamped, if unclamped it stays unclamped. These parameters are listed in the electrical diagram. I have seen...
  14. Replies
    9
    Views
    1,311

    I can't say what a 20 HP Haas will do, but a 20...

    I can't say what a 20 HP Haas will do, but a 20 HP Mazak will remove 11 pounds of 1018 in about 2 minutes, and it sounds like a hail storm. That is turning a 4" diameter slug not a bar though.
  15. Replies
    0
    Views
    477

    1993 Mazak H500/40N

    We have a 1993 Mazatech H500/40N for sale. Machine has a E-Stop that we are not able to find and don't want to pay for repair. We upgraded to a newer Mazak horizontal. This machine is available as a...
  16. Mazak lathes will call the last known offset for...

    Mazak lathes will call the last known offset for that tool, if that tool has not been called yet it will default to the primary offset. Call T0101 will bring up tool 1 offset 1. Call T0101.2 it will...
  17. Replies
    18
    Views
    1,061

    Make sure you have your radius set correctly in...

    Make sure you have your radius set correctly in tool offset. Half the end mill diameter.
  18. Replies
    10
    Views
    910

    I thought end mills are always set to "0"...

    I thought end mills are always set to "0" setting. I always have them set for that, but do not program in degrees. I use polar milling.
  19. If you are storing the program in the machine...

    If you are storing the program in the machine memory, 1 device moved from machine to machine. The ones in the link are for that purpose, they have ones that stay at the machine also. I think that is...
  20. Easiest thing I have ever used. DNC,...

    Easiest thing I have ever used.

    DNC, xlTRANSFER

    or

    Portable USB Connect from Shop Floor Automations

    I have used the first one on my 1995 Fanuc controlled Mori, and it is fine. I have used...
  21. Replies
    26
    Views
    3,213

    The biggest concern would be what control voltage...

    The biggest concern would be what control voltage your control needs. A lot of CNC machines need 24V DC. If your supply power is too high or too low, it will either burn up your boards/drives, or not...
  22. Replies
    1
    Views
    540

    Sounds like your hard drive went out. Timing...

    Sounds like your hard drive went out. Timing would be about right on a 2005.
  23. Replies
    9
    Views
    538

    Probably a dumb question, but did those sub...

    Probably a dumb question, but did those sub programs actuallymake it to the machine? Could it have timed out before finishing?
  24. Replies
    6
    Views
    1,339

    I got the file downloaded. Looking at the...

    I got the file downloaded. Looking at the drawing, I need to get in from the tail stock end, loosen 10 bolts to pop the drive loose. Then get the motor to orient and get my drive lug set correcty....
  25. Replies
    6
    Views
    1,339

    P.M. sent with my email Thanks

    P.M. sent with my email

    Thanks
Results 1 to 25 of 166
Page 1 of 7 1 2 3 4