Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    1
    Views
    48

    Erik Whenever I have a scan I forward it to...

    Erik
    Whenever I have a scan I forward it to that French site which has already thousands of manuals on it
    That way we create a big database
    Machines Outils: Manuels & Docs (Machinery Manuals &...
  2. Replies
    9
    Views
    500

    Place a heavy enough beam on the hollow site ...

    Place a heavy enough beam on the hollow site
    Then a ratchet strap around it and pull it straight
    At the end of the beam you plase some wood between beam and handrail to be able to overbent a bit...
  3. Replies
    25
    Views
    1,365

    I am puzzeled I see 6 terminals :willy_nilly:...

    I am puzzeled
    I see 6 terminals :willy_nilly:
    So you can switch all 3 phases
    Are you saying terminal 5 and 2 are shorted ??
    There a 3phase contacters that automaticly disconnect when there is...
  4. Make sure the ones you order to make are hobbed...

    Make sure the ones you order to make are hobbed Otherwise you better buy it from one of those places
    Peter
  5. It was on Ebay-kleinanzeigen.de...

    It was on Ebay-kleinanzeigen.de
    https://www.ebay-kleinanzeigen.de/s-anzeige/kupplung-fuer-drehbank-graziano-sag12-neu-ersatzteil/1174865842-84-1111

    Peter
  6. Did you ever ran a decent 135 or 150 ?? The...

    Did you ever ran a decent 135 or 150 ??
    The ability to make a smooth 0.01mm cut makes live easy
    Same on a HLVH

    Peter
  7. Many of us I imagen Peter

    Many of us I imagen

    Peter
  8. That would only count for if the stick out of the...

    That would only count for if the stick out of the tailstock was different for a good amount
    And that was not mentioned But could be possible

    Peter
  9. I looked up the manual and it seems the headstock...

    I looked up the manual and it seems the headstock of the Harrison M250 sits on the V of the bedway
    Sometimes the V is a bit wider as the V of the bedways making it adjustable anyhow
    But I think...
  10. You first level the bed Then you adjust the...

    You first level the bed
    Then you adjust the headstock

    In your case I think the bed is twisted and the headstock compensates for that twist
    Always first level the bedways Then do a 2...
  11. Pffffff Peter

    Pffffff

    Peter
  12. If it suits your workenvelop only slightly ...

    If it suits your workenvelop only slightly
    Schaublin 150
    Schaublin 150
    Schaublin 150
    Schaublin 150
    Schaublin 150
    Schaublin 150
  13. Source for electromagnetic clutches and brakes for Graziano SAG12 AO

    This compagny has a vast stock of electromagnetic clutches and brakes for European machine
    They advertise with clutches for the SAG12 particily
    I do not know if I mentioned these before ...
  14. Replies
    56
    Views
    4,065

    CJD Here is your chance Peter

    CJD
    Here is your chance


    Peter
  15. You mention me one thing in machining that is not...

    You mention me one thing in machining that is not dangerous please
    How much danger you want to endure is up to you
    I would ring them a
    Not all grinding stones are resin bond btw
    Many are...
  16. For those who question the strenght of a epoxied...

    For those who question the strenght of a epoxied ancor
    We had a M16 15cm deep pulled out It came out of the floor with more as a square foot of concrete attached to it
    That learned me if...
  17. I would not use soft solder between compressor...

    I would not use soft solder between compressor and tank as near the compressor it can get realy hot
    I have blown a PVC pipe once for that

    Peter
  18. Replies
    14
    Views
    1,698

    Once you have your Starrett level the whole...

    Once you have your Starrett level the whole thing again
    Is there any vissable wear on the ways???
    If not I think it is just that

    Peter
  19. No The S20x2 collets fit the Deckel SO and SOE...

    No
    The S20x2 collets fit the Deckel SO and SOE and with the proper adaptor the Deckel milling machines
    The S20x20 is in fact the treaded end of the collets and also the NT40 taper and also the...
  20. If it is not NT40 it has the taper for the...

    If it is not NT40 it has the taper for the M16x1,2mm collets
    Deckel never made a high speed head with S20x2 collets
    The M16x1,2 collets are rare
    RC machines in Luxembourg used to sell these...
  21. Picture or original spare parts drawing would...

    Picture or original spare parts drawing would help

    Peter
  22. Replies
    23
    Views
    1,018

    I know Even a bigger mess on a Deckel if...

    I know
    Even a bigger mess on a Deckel if flooded :D

    Peter
  23. Replies
    23
    Views
    1,018

    Problem with rust under the magnet on a surface...

    Problem with rust under the magnet on a surface grinder is that it can bend the table

    Peter
  24. Replies
    23
    Views
    1,018

    I hate to use coolant on a milling machine and...

    I hate to use coolant on a milling machine and almost never do
    It makes a real mess
    Speed a bit lower Feed on the high end
    All in all makes it faster if you account for the mess with coolant ...
  25. Replies
    5,332
    Views
    821,641

    Get a set with nylon wheels They roll better as...

    Get a set with nylon wheels They roll better as poly
    Swipe your floor And then once more
    On heavy machines I like to drag some timber along in case I loose a roller
    And I sometimes use a...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4