Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jim rozen

Page 1 of 60 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    25
    Views
    1,035

    [QUOTE=b.rett;3475722]Hello, I am not at a shop...

    [QUOTE=b.rett;3475722]Hello,
    I am not at a shop for a long while but need to oversee replacing a couple gears on an old (very old) Southbend lathe.

    Not for nothing, but those gears can be easily...
  2. Replies
    30
    Views
    2,357

    You "win" when you forget to bring one and have...

    You "win" when you forget to bring one and have to pony up the four bucks in the machine that sells them.
    And you receive in return-----------> one of your own items!

    Shortly thereafter the...
  3. Replies
    41
    Views
    2,024

    Wedding rings are best avoided in the shop. ...

    Wedding rings are best avoided in the shop.

    Ring Avulsion Injuries - Hand - Orthobullets

    Total deglovement of the fourth digit due to ring avulsion injury | BMJ Case Reports

    Note that in...
  4. Replies
    30
    Views
    2,357

    +1 on the hardinge machine set up as a turret...

    +1 on the hardinge machine set up as a turret lathe.

    Hypothetical story: At one time somebody's mom was hospitalized for a long time. The hospital charged $4 per parking event, paid via...
  5. Replies
    41
    Views
    2,432

    "I will answer any questions and measure, test,...

    "I will answer any questions and measure, test, photograph and basically do anything you may need ..."

    Please supply a photo of:

    Price tag on FP2

    and photo of:

    Price tag on HLVH
  6. Replies
    41
    Views
    2,155

    I finally took some photos of my test gear. ...

    I finally took some photos of my test gear. First is the General Radio ohm meter, it's shown reading
    a 100 GigOhm resistor - that's 10e11 ohms, or 100,000 meg ohms.

    Second is a hand-cranked...
  7. [QUOTE=stoneaxe;3473221]Having set the job up in...

    [QUOTE=stoneaxe;3473221]Having set the job up in the four jaw and a center, I was surprised to see .005 runout in the free end, after I pulled the center out.

    Old time machinist would say of...
  8. Pelton wheel - Wikipedia...

    Pelton wheel - Wikipedia

    There is an abandoned estate north of here on the hudson river, where the land has been deeded back to the
    state for conservation land. Hiking through there one finds...
  9. Replies
    1,282
    Views
    105,074

    And when they did supply the sim companies with...

    And when they did supply the sim companies with the data files, the files did not include the behavior that the MCAS system caused.
    That for me is the most damning aspect of the entire episode. ...
  10. I will leave that to: a) the experts at the...

    I will leave that to:

    a) the experts at the USSC and
    b) to the 'experts' here as they no doubt have voluminous ideas about what it all means.

    When the PM board becomes elevated to the...
  11. Somewhat off topic but still a true story. I...

    Somewhat off topic but still a true story.

    I was working at a lab tech in the University of Wisconsin electronics shop many years ago. One of my jobs was using a walker turner floor drill press...
  12. Replies
    1,282
    Views
    105,074

    [QUOTE=EmanuelGoldstein;3472079]Oh, they're...

    [QUOTE=EmanuelGoldstein;3472079]Oh, they're "mistakes" now but when Boeing shit on all their employees, moved to Chicago, sent three-fourths of the work overseas to "maximize shareholder value" they...
  13. None of the other bill of rights amendments have...

    None of the other bill of rights amendments have any "observations." The authors were quite sparing of words, and only used
    ones that were specifically needed. Every word in each one does ...
  14. This is probably not a hardinge headstock, the...

    This is probably not a hardinge headstock, the top-off is that the largest cone on the pulley is at the front, whereas
    the hardinge machines of that vintage have the largest pulley at the left side...
  15. [QUOTE=Scottl;3472233] "I will once again repeat...

    [QUOTE=Scottl;3472233]
    "I will once again repeat the challenge first raised by author Stephan Halbrook."

    Well since the USSC (and lower courts as well!) are no longer able to make any ruling that...
  16. "comply with the dictats of urban rulers." ...

    "comply with the dictats of urban rulers."

    Kinda sucks when your gerrymander falls apart eh.
  17. Status level simply equals age of poster. You...

    Status level simply equals age of poster.
    You kids get off my lawn.
  18. "I don't HAVE to be an Attorney to do an...

    "I don't HAVE to be an Attorney to do an Executor's job."

    You're not a lawyer but you play one on the internet?

    Alternative response: TMI
  19. Spot the top of the cross slide and the underside...

    Spot the top of the cross slide and the underside of the compound slide and scrape to correct the
    lack of contact. You'll need to remove the pivot pin from one of those, I forget if its the top or...
  20. Replies
    1,282
    Views
    105,074

    You could have just stopped that after "together."

    You could have just stopped that after "together."
  21. Just make the rules clear: 1) don't say atlas...

    Just make the rules clear:

    1) don't say atlas
    2) don't say unimat (sherline)
    3) don't say shaper
    4) don't be an askhole.
  22. Replies
    23
    Views
    1,173

    "Big chucks don't like high RPM, most especially...

    "Big chucks don't like high RPM, most especially on JR HS training-wheel mass lathe..."

    SB heavy ten will use a 9" six-jaw chuck just fine. 8 inch even easier.
    Don't put it on much but some...
  23. Replies
    29
    Views
    1,955

    Then bring along an older machinist. 1) they...

    Then bring along an older machinist. 1) they know what they're looking at, 2) they already have that stuff so they won't
    try to outbid you for it.

    I'd offer to go with but obviously live near...
  24. [QUOTE=Cobranut;3468335] NO law will stop a...

    [QUOTE=Cobranut;3468335]
    NO law will stop a criminal who is willing to commit MURDER from using guns to commit his crime.

    Laws do stop people from obtaining guns. Guy shows up at a gun shop. ...
  25. Replies
    41
    Views
    2,155

    [QUOTE=JST;3469177] Just did not want to...

    Just did not want to confuse the man with the question - my hand-crank biddle meter has the meter needle
    looking exactly like his photo above, when it's not in operation. With no resistor across...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4