Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: solidworkscadman

Page 1 of 39 1 2 3 4

Search: Search took 0.01 seconds.

  1. good deal on a nice machine

    good deal on a nice machine
  2. sold The message you have entered is too...

    sold


    The message you have entered is too short. Please lengthen your message to at least 10 characters.
  3. Replies
    5
    Views
    404

    I have a few fanuc 6t boards if you end up...

    I have a few fanuc 6t boards if you end up needing one,

    I just scrapped a couple machines that ran good and kept the boards

    Ill give you a much better deal then buying from fanuc
  4. i was just quoted 1.57 a lb for scrap brass

    i was just quoted 1.57 a lb for scrap brass
  5. 274533 274534 274535 274536

    274533

    274534

    274535

    274536
  6. Harig 025-100 6 Inch Swing, 7 Inch Distance Cylindrical Grinder

    Harig 025-100

    Comes with original box

    Distance Between Centers (Inch) 7
    Swing (Inch) 6
    Voltage 115
    Wheel Spindle Speed (RPM) 180.00; 360.00
    ...
  7. work long hours and save to have cash on hand....

    work long hours and save to have cash on hand. Then find a local machine shop auction and bid on a machine
  8. Replies
    188
    Views
    9,847

    i would buy another one YouTube...

    i would buy another one

    YouTube
  9. Nice looking lathe

    Nice looking lathe
  10. Replies
    89
    Views
    6,472

    I have been told by yamazens engineer Joe tsun it...

    I have been told by yamazens engineer Joe tsun it was not recommended to go above 1/2" endmill on the bt30
  11. sold The message you have entered is too...

    sold

    The message you have entered is too short. Please lengthen your message to at least 10 characters
  12. sold The message you have entered is too...

    sold

    The message you have entered is too short. Please lengthen your message to at least 10 characters
  13. The memory that added will not change the...

    The memory that added will not change the computing proessor that the control is equipped with,

    look into the Risc proessor for fanuc
  14. Replies
    11
    Views
    1,888

    youll want to maintain 55 in the shop at least...

    youll want to maintain 55 in the shop at least for storage here in new england
  15. nice machine

    nice machine
  16. sold The message you have entered is too...

    sold

    The message you have entered is too short. Please lengthen your message to at least 10 characters.
  17. bump 5,000

    bump

    5,000
  18. bump 5,000

    bump

    5,000
  19. Bump 15,000

    Bump

    15,000
  20. Once you sell that system, give this a gander...

    Once you sell that system,

    give this a gander Mach-1 Systems - R8 Quick Change Tooling for Knee Mills & Bed Mills
  21. MA 01915 The message you have entered is...

    MA 01915



    The message you have entered is too short. Please lengthen your message to at least 10 characters.
  22. I run my programs through Cimco and backplot the...

    I run my programs through Cimco and backplot the gcode real quick then to the machine and keep an eye on the first few movements at 25% and single block, then its off to the races
  23. 266280 266281 266282 266283

    266280
    266281
    266282
    266283
  24. 2013 Deltech SPX HTD20 Refrigerated Compressed Air Dryer Filter 20 CFM

    Deltech SPX HTD20
    Refrigerated Compressed Air Dryer Filter 20 CFM

    Almost NEW!

    Has about 20 hours of run time, was too small for our needs and then put on the shelf

    Manuals included

    650
  25. new collets from R-8 Collets 1/8" - 3/4" - Mach-1...

    new collets from R-8 Collets 1/8" - 3/4" - Mach-1 Systems are 79.00 each

    the complete system including the drawbar and tooling is 1495.00
    https://www.youtube.com/watch?v=YaiZC93ASJ8&t=1s

    We...
Results 1 to 25 of 956
Page 1 of 39 1 2 3 4