Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Hobby Shop

Page 1 of 29 1 2 3 4

Search: Search took 0.01 seconds.

  1. Yep, that’s it. The brass tube is supposed to...

    Yep, that’s it. The brass tube is supposed to telescope like the table drain tube.
  2. Hopefully the timer was on from the beginning but...

    Hopefully the timer was on from the beginning but it’s highly unlikely. The feed shaft tube is broken ( under the table right side). You’ll want to fix that before any chips make their way in to the...
  3. Replies
    5
    Views
    289

    WTB: NMTB #50 tool holders

    If you have any collecting dust & rust send a PM or post here.
    I’d like 1/2”, 1”, 1-1/4” and 1-1/2”.

    Andy
  4. Replies
    64
    Views
    4,069

    Looks like it’s coming along really well.:D I’ll...

    Looks like it’s coming along really well.:D I’ll be replacing my toggle switch on my 2D with a push button sometime in the future. I hardly ever wear a hat but one day I did and now my pinkie finger...
  5. Slivers, grit and general contamination on the...

    Slivers, grit and general contamination on the strip. Its been a while but I’ve built them like that on aluminum and SS dies before. Die changes are so fast now a days it makes more sense to dieset...
  6. Replies
    32
    Views
    1,122

    Around here about $3k for a standard rip/replace...

    Around here about $3k for a standard rip/replace for just the pipes. $12-20k for a complete engineered field. You can perk it yourself with the health department and have a better idea of what you’re...
  7. Watch eBay for the Unisorb feet to come up. You...

    Watch eBay for the Unisorb feet to come up. You have to be patient but you can usually find them $50-$75 for a set, (4 leveling feet). I use them for all my mills and have been happy with them.
    ...
  8. Replies
    32
    Views
    1,915

    I have no idea what you’re talking about but...

    I have no idea what you’re talking about but single hit dies are run EVERYDAY in automatic presses. Time them out, put them in a line and run the parts manually at each station. I’m not saying you...
  9. Replies
    32
    Views
    1,915

    I stopped reading after the first couple of posts...

    I stopped reading after the first couple of posts but Its only 5” flanged washer. A deep draw to me, is anything over 10”s in a single hit. Think floorpans, fuel tank half, hoods, pickup box sides. A...
  10. Replies
    23
    Views
    2,420

    Did you remove the bushing cover on the knee...

    Did you remove the bushing cover on the knee (front right with 3 bolts) and pull the spline shaft out the front? After the shaft is removed everything “should” come right off.
  11. Replies
    23
    Views
    2,420

    Did someone remove the over limit trip dogs?...

    Did someone remove the over limit trip dogs? They’re on all 3 axis that kick out the feed in case the adjustable dogs are removed. You should be able to remove the feed shaft and drive box without...
  12. I have no idea what’s going on here. If you...

    I have no idea what’s going on here. If you figure it out....let me know.

    Andy
  13. Replies
    16
    Views
    2,439

    I’ve had a lot of 2H and large LL sets but I...

    I’ve had a lot of 2H and large LL sets but I haven’t seen ANY 11p change gears and worms/wheels for the
    1-2HL/2CHL low lead.

    Consider yourself lucky with the 1:3 worm/wheel. That’s the most...
  14. Thanks, PM sent.

    Thanks,
    PM sent.
  15. Replies
    627
    Views
    41,111

    Is it a coincidence they’re now talking about...

    Is it a coincidence they’re now talking about applying $11billion in Airbus retaliatory tariffs on the EU after all the 737 Max orders have been canceled? The Gov. needs to step out of they way on...
  16. Replies
    9
    Views
    889

    Yes. These parts are brand new. The PO of my...

    Yes. These parts are brand new. The PO of my grinder had them sitting on a shelf since the early 70’s. They only used diamond wheels to grind carbide broaches.
  17. Yes. Almost all the parts from a 2H and 2HL are...

    Yes. Almost all the parts from a 2H and 2HL are interchangeable.
  18. Replies
    9
    Views
    889

    The set screws are supposed to lock in the...

    The set screws are supposed to lock in the dovetail so they don’t fall out when changing the wheels. After dropping the wheel I noticed it was slipping in the holder. My shoes are only touching on...
  19. Replies
    9
    Views
    889

    Mebfab, if you need a picture, I can pull one...

    Mebfab, if you need a picture, I can pull one off. My #11 uses the cylinder wheels also. I’m not positive but I think the “shoes” were bronze.
  20. Replies
    23
    Views
    1,742

    Its good to hear everything is coming along. I...

    Its good to hear everything is coming along. I have a 3hp 2HL motor I have no use for. If you can figure out what you need......The parts are yours for the ride.

    Andy
  21. Maybe I was a little harsh in my assessment. What...

    Maybe I was a little harsh in my assessment. What won’t work for me, might work for you? For me, 550rpm is a limiting factor but it can absolutely make chips. If the price is right and you’re...
  22. Having been down that rabbit hole to many times,...

    Having been down that rabbit hole to many times, I wouldn’t take it if he was giving it away. There was a L&S 16”x54” Powerturn 2000rpm on the Cincinnati CL a couple months ago that looked like it...
  23. Replies
    50
    Views
    4,214

    He should give him back his money and relist it. ...

    He should give him back his money and relist it.
    :willy_nilly:“Free” to anyone except the last guy I sold it to. :willy_nilly:

    Hobby Shop is first in line. :stirthepot:
  24. Replies
    7
    Views
    1,430

    Deleted. No time for a road trip.

    Deleted. No time for a road trip.
  25. Thanks a lot, I’m missing all of those. Sending...

    Thanks a lot, I’m missing all of those. Sending PM for Pmt info now.

    Andy
Results 1 to 25 of 711
Page 1 of 29 1 2 3 4